JVC DT-3D24G1U DT-3D24G1U Operation Manual - Page 30
Troubleshooting
View all JVC DT-3D24G1U manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 30 highlights
Troubleshooting Solutions to common problems related to the monitor are described here. If none of the solutions presented here solve the problem, unplug the monitor and consult an authorized dealer or service center. Symptom Probable cause and corrective action Page Cannot turn on the unit. No picture with the power on. No sound. "Out of range" appears. ● Press the button to turn it on. ● Plugs should be firmly inserted. ● Turn on the AC power switch on the back of this product. ● If you do not turn on the monitor by pressing the button while the DC power is turned on, disconnect the DC connector, set up the DC power within the operating range, and then connect the connector again. ● Select the correct input using the INPUT SELECT buttons. ● Connect the signal cable firmly. ● Turn on the power of the connected component and set the output correctly. ● Check whether the input signal format is acceptable on the monitor. ● Adjust the volume level. ● Deactivate the muting function. ● Connect the signal cable firmly. ● Turn on the power of the connected component and set the output correctly. ● Input a signal compatible with the unit. ● Select the correct input using the INPUT SELECT buttons. ● Connect the signal cable firmly. "NO SYNC" appears. ● Turn on the power of the connected component and output video signals. Or, check whether the video output of the component (video output setting of the VCR or graphic board of the computer) is set correctly. ● Adjust each picture adjustment knob on the front panel or adjust the items of "PICTURE SUB ADJ." in the SET-UP MENU. Or, perform "reset" in "PICTURE SUB ADJ." Wrong color, no color. ● Check whether the setting of COLOR OFF or SCREENS CHECK buttons are appropriate. ● Adjust the items of "WHITE BALANCE SET." in the SET-UP MENU. Or, perform "reset" in "WHITE BALANCE SET." The picture becomes blurred. ● Adjust the picture contrast or brightness by using the adjustment knobs on the front panel. Or, adjust "CONTRAST" or "BRIGHT" of "PICTURE SUB ADJ." in the SET-UP MENU. Wrong picture position, wrong ● Check whether the setting of 1:1 is appropriate. picture size. For some signals, the picture cannot be displayed fully in the ● Check "ASPECT" of the MAIN MENU, and " SD4:3 LARGE " under the SET-UP MENU "FUNCTION SETTING." ● Check whether the input signal format is acceptable on the monitor. effective screen area. There is no sure method to solve this problem. Some items do not appear on the menu. ● The items which are not available for the current input or the current input signal are not displayed on the menu. Change the input or the input signal. ● The items controlled by the MAKE system do not appear on the menu. Buttons on the monitor do not work. ● Set "CONTROL LOCK" in the SET-UP MENU to "OFF." ● You cannot use the buttons for the items controlled by the MAKE system. Disable the external control. ● Press the 3D button to enter the 3D mode. 3D viewing is not available. ● Press the SELECT button to change the 3D viewing format (when inputting existing 3D images). ● Set the 3D format compatible with input images in "SDI FORMAT 1/SDI FORMAT 2" or "DVI FORMAT 1/ DVI FORMAT 2" under the MAIN MENU "3D SETTING." ● Press the MIX button to enter the MIX mode. Cannot enter the MIX mode. ● Input L and R images in the same format compatible with the MIX mode. ● Input 3G SDI LEVEL B Dual Stream into the SDI IN 1/L terminal. The image is distorted or cannot ● Set "FRAME SYNC." under the MAIN MENU "3D SETTING" to "ON" or "OFF." be synchronized in MIX mode. 9 7 7 9 7 - 33, 34 8 9 7 - 11, 33, 34 9 7 - 8, 23 9 23 8, 23 9 20, 23 33, 34 - 26 25 26, 27 9, 13 9, 13 19 9, 13 33 - 19 The following are not malfunctions. ● When a still image is displayed for a long time, it may remain indistinctly on the screen after the picture has changed. Though the remaining picture will disappear after a while, there may be a case that it remains for a long period depending on the length of time the still image was displayed for. This is due to the characteristics of the LCD display and is not a malfunction. ● Red spots, blue spots and green spots on the panel surface are a normal characteristic of LCD displays, and not a problem. The LCD display is built with very high precision technology; however, be aware that a few pixels may be missing or constantly lit. ● The following symptoms are problems only when pictures or sounds are not played back normally. ● A slight electric shock occurs when you touch the monitor. ● The top and/or rear panel of the monitor becomes hot. ● The monitor emits a cracking noise. ● The monitor emits a mechanical noise. 30