JVC FS-V100 Instruction Manual - Page 15

Basics of Using the CD Player - Normal Play Playing a CD 1 Insert a CD. 2 Press the CD #/8 button. The first track of the CD begins playing. Track number Playback time • The track number that has already played disappears from the music calendar. • The CD Player automatically stops when the last track of the CD has finished playing. To stop playing the CD, press the 7 button. The following information for the CD is displayed. Total track number Total playback time To stop playing and remove the CD, press the CD OPEN/ CLOSE 0 button on the Unit or CD 0 button on the Remote Control to open the CD cover. Then remove the CD. To pause, press the CD #/8 button. The playback time flashes on the display. To cancel pause, press the same button again. Play continues from the point where it was paused. Selecting a track During playback, press the 4 or ¢ button (or the , DOWN or UP button on the Remote Control) to select the track you want. The selected track starts playing. • Press the ¢ button (or the > or UP button on the Remote Control) once to skip to the beginning of the next track. • Press the 4 button (or the < or DOWN button on the Remote Control) to skip to the beginning of the track being played. Press twice quickly to skip to the beginning of the previous track. • When the > or < button on the Remote Control is held down, the tracks are successively skipped. Selecting a passage within a track ---- Holding down the 4 or ¢ button (or the DOWN or UP button on the Remote Control), during playback, will fast-forward/reverse the CD so you can quickly find a particular passage in the track you are listening to. Programing the Playing Order of the Tracks You can program the playing order of the tracks using the Remote Control. s You can program up to 20 tracks in any desired order including the same tracks. s You can only make a program when the CD Player is stopped. 1 Insert a CD. 2 Press the CD #/8 button. 3 Press the 7 button to stop the CD. 4 Press the PROGRAM button. The System enters the programing mode and the PROGRAM indicator lights up. PROGRAM PROGRAM RANDOM 5 Press the > or < button to select the track to program. > button: Increases the track number by 1. < button: Decreases the track number by 1. • When the > or < button is held down, the track number changes rapidly. 6 Press the SET button. Program order number SET Total playback time of the programed tracks 7 Repeat steps 5 and 6 to select the other tracks for the program. You can see the total playback time of programed tracks on the display. You can also see the programed tracks on the music calendar. 8 Press the CD #/8 button. The System plays the tracks in the order you have programed them. s You can skip to a particular program track by pressing the 4 or ¢ button (or the , DOWN or UP button on the Remote Control) during Program Play. s To stop playing, press the 7 button once. To confirm the programed tracks while the CD player is stopped, press the PROGRAM button; the tracks making up the program will successively be displayed in the programed order. To delete all the tracks in the program while the CD player is stopped, press the 7 button. Pressing the CD 0 button on the Remote Control (or the CD OPEN/CLOSE 0 button on the Unit) to open the CD cover will also clear the programed tracks. To exit from the program mode while the CD player is stopped, press the 7 button to light off the PROGRAM indicator. All the programed tracks will be cleared. Notes: • If the total playback time of the programed tracks exceeds 99 minutes 59 seconds appears on the display. • If you try to program the 21st track, "FULL" appears on the display for about 2 seconds. Modifying the program Modify the contents of the program while the CD Player is stopped. Each time you press the CANCEL button, the last track in the program is deleted. To add new tracks to the end of the program, repeat above steps 5 to 7. EN10-22.FS-V100[J]f 11 12/12/00, 10:32 AM 11