JVC HAW600RF Instructions - Page 11

Basic operations, Listening to the sound from the base, station - - headphones

Get JVC HAW600RF - Headphones - Binaural PDF manuals and user guides
UPC - 046838026744
View all JVC HAW600RF manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

ENGLISH Basic operations Listening to the sound from the base station The base station works as the FM transmitter and send sound to the headphones. Precaution Turn down the volume of the headphones with the VOL dial before turning on its power to avoid excessive volume. 1 Start playback on the AV equipment connected with the base station. The base station turns on automatically and starts to transmit FM signals (Auto Power On function). The POWER indicator of the base station lights up. • In some situations, the power may not be turned on automatically by the input sound (e. g. a song with a quiet opening or fade in). This is not a malfunction. 2 Press POWER on the headphones to turn on the power. The POWER indicator lights up and the headphones automatically starts to tune in to the signal from the base station (Auto Tuning function). The AUTO SCAN indicator lights up when tuned in. • Press the center of the button firmly when pressing POWER. Pressing the edge may not turn on the power. • Charge the battery in the following cases. The battery ran out: - The POWER indicator does not light up after pressing POWER. - The AUTO SCAN indicator does not light up though the POWER indicator lights up. • No sound is heard while Auto Tuning. It takes a few seconds to tune in. • Press AUTO SCAN when the sound does not come out properly. 3 Adjust the volumes of the AV equipment and the headphones. • Adjust the volumes within the area about 7 m (23 ft.) from the base station to get optimum signal reception. • You can get better sound by setting the volume of the AV equipment as high as possible without causing distortion and that of the headphone lower (except when connecting the AV equipment through LINE OUT jacks). To Turn off the units Press POWER on the headphones and stop playback on the AV equipment. The headphones' POWER indicator goes off. • The base station automatically turns off if no signals come in for about four minutes (Auto Power OFF function). • The white noise may come out when the base station turns off. Take off and turns off the headphones after using. 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
7
ENGLISH
Basic operations
Listening to the sound from the base
station
The base station works as the FM transmitter
and send sound to the headphones.
Precaution
Turn down the volume of the headphones with
the VOL dial before turning on its power to
avoid excessive volume.
1
Start playback on the AV
equipment connected with the
base station.
The base station turns on automatically and
starts to transmit FM signals (Auto Power
On function).
The POWER indicator of the base station
lights up.
•
In some situations, the power may not
be turned on automatically by the input
sound (e. g. a song with a quiet opening
or fade in). This is not a malfunction.
2
Press POWER on the
headphones to turn on the
power.
The POWER indicator lights up and the
headphones automatically starts to tune in
to the signal from the base station (Auto
Tuning function).
The AUTO SCAN indicator lights up when
tuned in.
•
Press the center of the button firmly
when pressing POWER. Pressing the
edge may not turn on the power.
•
Charge the battery in the following cases.
The battery ran out:
– The POWER indicator does not light
up after pressing POWER.
– The AUTO SCAN indicator does not
light up though the POWER indicator
lights up.
•
No sound is heard while Auto Tuning. It
takes a few seconds to tune in.
•
Press AUTO SCAN when
the sound does not come out
properly.
3
Adjust the volumes of the
AV equipment and the
headphones.
•
Adjust the volumes within the area about
7 m (23 ft.) from the base station to get
optimum signal reception.
•
You can get better sound by setting the
volume of the AV equipment as high
as possible without causing distortion
and that of the headphone lower (except
when connecting the AV equipment
through LINE OUT jacks).
To Turn off the units
Press POWER on the headphones and
stop playback on the AV equipment.
The headphones’ POWER indicator
goes off.
• The base station automatically turns off if no
signals come in for about four minutes (Auto
Power OFF function).
• The white noise may come out when the base
station turns off. Take off and turns off the
headphones after using.