JVC HR-XVC18B Instruction Manual - Page 12

Optional TV Connections, Audio Connection for DVD

Get JVC HR-XVC18B PDF manuals and user guides View all JVC HR-XVC18B manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

RF coaxial connection Connect the RF.OUT jack on the DVD+VCR to the antenna in jack on the TV using the supplied 75-ohm Coaxial Cable (R). Optional TV Connections These connections support only DVD playback. The tuner and VCR still output through the RF.OUT (R) or DVD/VCR OUT (A, V) jacks. How to set the DVD+VCR's RF output channel 1. When the DVD+VCR is turned off, press and hold both CH - and CH + on the front panel for more than five seconds. "RF03" or "RF04" appears in the display window. 2. Press either CH - or CH + to change the RF output channel (RF03 or RF04). Tune the TV to this channel. 3. Turn off the DVD+VCR. Audio/Video connection 1. Connect the DVD/VCR VIDEO OUT jack on the DVD+VCR to the video in jack on the TV using an optional video cable (V). 2. Connect the Left and Right DVD/VCR AUDIO OUT jacks on the DVD+VCR to the audio left/right in jacks on the TV (A1) using an optional audio cables. Note: If you use this connection, set the TV's source selector to VIDEO. Component Video / Progressive Scan connection If your television is a high-definition or "digital ready" television, you may take advantage of the DVD+VCR's progressive scan output for the highest video resolution possible. 1. Connect the COMPONENT/PROGRESSIVE SCAN VIDEO OUT jacks on the DVD+VCR to the corresponding in jacks on the TV using an optional Y Pb Pr cable (C). 2. Connect the Left and Right AUDIO OUT jacks of the DVD+VCR to the audio left/right in jacks on the TV (A2) using an optional audio cables. Notes: • When you use Composite Video signal, set the Progressive Scan to "Off" on the setup menu. • Progressive scan does not work with the Composite video connections (yellow VIDEO OUT jack). • If your TV does not accept the Progressive Scan format, the picture will appear scrambled. Switch to composite video output. Audio Connection for DVD You can listen to playback using DVD/VCR AUDIO OUT (A1), AUDIO OUT (A2), COAXIAL (X) and RF. OUT (R) connections. COAXIAL (X) and AUDIO OUT (A2) is used only for listening to DVD playback. (See page 11.) Connecting to an amplifier equipped with two channel analog stereo Connect the Left and Right AUDIO OUT (or DVD/VCR AUDIO OUT) jacks on the DVD+VCR to the audio left and right in jacks on your amplifier, receiver, or stereo system using an optional audio cables (A1, A2). 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
12
RF coaxial connection
Connect the RF.OUT jack on the DVD+VCR to
the antenna in jack on the TV using the supplied
75-ohm Coaxial Cable
(R)
.
How to set the DVD+VCR
’
s RF output
channel
1.
When the DVD+VCR is turned off, press and
hold both CH - and CH + on the front panel for
more than five seconds.
“
RF03
”
or
“
RF04
”
appears in the display window.
2.
Press either CH - or CH + to change the RF
output channel (RF03 or RF04). Tune the TV
to this channel.
3.
Turn off the DVD+VCR.
Audio/Video connection
1.
Connect the DVD/VCR VIDEO OUT jack on
the DVD+VCR to the video in jack on the TV
using an optional video cable
(V)
.
2.
Connect the Left and Right DVD/VCR AUDIO
OUT jacks on the DVD+VCR to the audio
left/right in jacks on the TV
(A1)
using an
optional audio cables.
Note:
If you use this connection, set the TV
’
s source selector
to VIDEO.
Optional TV Connections
Optional TV Connections
These connections support only DVD playback.
The tuner and VCR still output through the
RF.OUT
(R)
or DVD/VCR OUT
(A, V)
jacks.
Component Video / Progressive Scan
connection
If your television is a high-definition or
“
digital
ready
”
television, you may take advantage of the
DVD+VCR
’
s progressive scan output for the high-
est video resolution possible.
1.
Connect the COMPONENT/PROGRESSIVE
SCAN VIDEO OUT jacks on the DVD+VCR to
the corresponding in jacks on the TV using an
optional Y Pb Pr cable
(C)
.
2.
Connect the Left and Right AUDIO OUT jacks
of the DVD+VCR to the audio left/right in jacks
on the TV
(A2)
using an optional audio cables.
Notes:
•
When you use Composite Video signal, set the
Progressive Scan to
“
Off
”
on the setup menu.
•
Progressive scan does not work with the Composite
video connections (yellow VIDEO OUT jack).
•
If your TV does not accept the Progressive Scan for-
mat, the picture will appear scrambled. Switch to
composite video output.
Audio Connection for DVD
Audio Connection for DVD
You can listen to playback using DVD/VCR
AUDIO OUT
(A1)
, AUDIO OUT
(A2)
, COAXIAL
(X)
and RF. OUT
(R)
connections. COAXIAL
(X)
and AUDIO OUT
(A2)
is used only for listening to
DVD playback. (See page 11.)
Connecting to an amplifier equipped with two
channel analog stereo
Connect the Left and Right AUDIO OUT (or
DVD/VCR AUDIO OUT) jacks on the DVD+VCR
to the audio left and right in jacks on your amplifi-
er, receiver, or stereo system using an optional
audio cables
(A1, A2)
.