JVC TK-C215VP4U Instructions - Page 8

Safety Precautions, continued, Introduction

Get JVC TK-C215VP4U - CCTV Camera PDF manuals and user guides
UPC - 046838027475
View all JVC TK-C215VP4U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

Introduction Safety Precautions (continued) ⅷ The unit is to be powered by a DC 12 V or an AC 24 V power supply. ⅷ The unit is to be powered by a UL Listed DC 12 V or an AC 24 V power supply. (For U type) ⅷ The AC 24 V and 12 V DC power supply shall conform to the following: Class 2 only (For USA), Isolated power supply only (For Europe). ⅷ This installation should be made by a qualified service person and should conform to all local codes. ⅷ This installation shall be in accordance with the National Electrical Code, ANSI/NFPA 70. ⅷ Any Mention in this manual of Alarm inputs have not been evaluated by UL to be used for Burglar Alarm Functionality. ⅷ When mounting this unit to the ceiling or wall, mount it to a secure location where it can support the mass of this unit. When mounting to an insecure location, make sure to carry out reinforcement of the ceiling or wall before installation. ⅷ The rating label is adhered to the bottom surface of the camera unit. ⅷ The camera unit may fall if the mounting screw or piping is not properly tightened. Ensure that the screws and nuts are properly tightened. ⅷ We do not accept liability for any damage to the camera in cases when it is dropped because of incomplete installation due to not observing the installation instructions correctly. Please be careful when installing the camera. ⅷ Do not install the camera near lighting equipment with a high temperature, such as spotlights. Doing so may cause malfunction or fire. ⅷ Before starting an important recording, be sure to perform a test recording in order to confirm that a normal recording is possible. ⅷ We will not provide any compensation whatsoever for the contents to be recorded or loss of opportunities when recording is not properly performed due to malfunction of the video camera, VTR, hard disk recorder or video tape. ⅷ Before touching the camera unit, make sure to touch the metal surface of the [MONITOR] terminal to discharge any static electricity from your body. Static electricity may cause the camera to malfunction. 4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
4
Introduction
²
The unit is to be powered by a DC 12 V or an
AC 24 V power supply.
²
The unit is to be powered by a UL Listed DC
12 V or an AC 24 V power supply. (For U type)
²
The AC 24 V and 12 V DC power supply shall
conform to the following: Class 2 only (For
USA), Isolated power supply only (For
Europe).
²
This installation should be made by a qualified
service person and should conform to all local
codes.
²
This installation shall be in accordance with
the National Electrical Code, ANSI/NFPA 70.
²
Any Mention in this manual of Alarm inputs
have not been evaluated by UL to be used for
Burglar Alarm Functionality.
²
When mounting this unit to the ceiling or wall,
mount it to a secure location where it can
support the mass of this unit. When mounting
to an insecure location, make sure to carry out
reinforcement of the ceiling or wall before
installation.
²
The rating label is adhered to the bottom
surface of the camera unit.
²
The camera unit may fall if the mounting screw
or piping is not properly tightened. Ensure that
the screws and nuts are properly tightened.
²
We do not accept liability for any damage to
the camera in cases when it is dropped
because of incomplete installation due to not
observing the installation instructions
correctly. Please be careful when installing the
camera.
²
Do not install the camera near lighting
equipment with a high temperature, such as
spotlights. Doing so may cause malfunction or
fire.
Safety Precautions
(continued)
²
Before starting an important recording, be
sure to perform a test recording in order to
confirm that a normal recording is possible.
²
We will not provide any compensation
whatsoever for the contents to be recorded or
loss of opportunities when recording is not
properly performed due to malfunction of the
video camera, VTR, hard disk recorder or
video tape.
²
Before touching the camera unit, make sure
to touch the metal surface of the [MONITOR]
terminal to discharge any static electricity
from your body. Static electricity may cause
the camera to malfunction.