JVC TM-H1950CGU Instruction Manual - Page 15
How To Use The Menu, Functions
View all JVC TM-H1950CGU manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 15 highlights
HOW TO USE THE MENU FUNCTIONS (cont'd) Set-up menu items PICTURE SUB ADJ. CONTRAST BRIGHT CHROMA PHASE H. POSITION V. POSITION WHITE BALANCE DRIVE R. DRIVE B. DRIVE CUT OFF R. CUT OFF G. CUT OFF B. CUT OFF CONTROL LOCK STATUS DISPLAY REMOTE SYSTEM INPUT REMOTE Purpose Settings Image sub adjustment Adjusts contrast. Adjusts brightness. Adjusts color density. Adjusts hue. Selects CONTRAST/BRIGHT/CHROMA/PHASE. The selected setting screen is shown. Select the function display for adjustment. -10 -9 • • -01 00 +01 • • +09 +10 - 10 - 9 • • - 01 00 +01 • • +09 +10 *1 -10 -9 • • -01 00 +01 • • +09 +10 *1 -10 -9 • • -01 00 +01 • • +09 +10 Adjusts the horizontal position of the screen (+: Horizontal position shifts to the right/-: Horizontal position shifts to the left) - 5 01 00 +1 5 Adjusts the vertical position of the screen (+: Vertical position moves up/-: Vertical - 5 01 00 +1 5 position moves down) Adjusts the white balance. Adjusts red level. Adjusts blue level. Adjusts red cut off. Adjusts green cut off. Adjusts blue cut off. Selects the drive (DRV) or cut off (CUTO) adjustment. The selected setting screen is shown. Select the function display for adjustment. -20 -19 • • -01 00 +01 • • +19 +20 - 20 - 1 9 • • - 01 00 +01 • • +19 +20 - 20 - 1 9 • • - 01 00 +01 • • +19 +20 -20 -19 • • -01 00 +01 • • +19 +20 - 20 - 1 9 • • - 01 00 +01 • • +19 +20 Sets the operation buttons on the front panel to control lock mode. OFF ON Sets the status display of the color system. O F F O N Sets the external control function method. M A K E T R G . *2 Sets external control of input selection. (Shown only when REMOTE SYSTEM is A - D A / B *2 set to MAKE.) *1 May not be shown depending on the type of signals input. *2 Refer to HOW TO USE EXTERNAL CONTROL on page 18 for more details. 4. To set the other set-up menu items, repeat the procedures 2 and 3. 5. Press the MENU button to quit. MENU Front panel Function button displayed MENU EXIT Contents Quit (or Release) the screen Note: Setting MAKE TRG. A-D A/B Description Make contact system: Controls the function using the control terminal's short-circuit and open (short-circuits or opens 15th terminal (GND)). Trigger system: Controls the function by short-circuiting (shortcircuits or opens 15th terminal (GND)) with pulse (about 1 sec.) Switches the input by short-circuiting a specified signal line in INPUT A, B, C, or D. Switches between INPUT A and INPUT B with D-sub pin 2. 14 Notes: ● When the CONTROL LOCK function is set to ON, pressing operation buttons on the front panel will display the message "CONTROL LOCK ON!" on the screen for about 3 seconds. ● The CONTROL LOCK function is maintained even when the power is turned off. ● To turn off the CONTROL LOCK function, while holding the MENU button press the CHROMA/PHASE button. Then set the CONTROL LOCK function to OFF. ● Even when the CONTROL LOCK function is set to ON, the following operations are available: - Power Switch operation - Volume control with the VOLUME/ SELECT buttons - Display or disappear of the screen. ● The STATUS DISPLAY function can be set to display (ON) or not display (OFF) the present color system when the power is turned on or the input signal is changed. Refer to page 9 for more information. ● When REMOTE SYSTEM is set to MAKE and any one of the INPUT A to D buttons, the UNDER SCAN button, COLOR OFF button or the ASPECT button is pressed, "REMOTE ON!" appears on screen for about 3 seconds. (Not shown with CONTROL LOCK set to ON.) ● When REMOTE SYSTEM is set to TRG, the front panel controls can be operated. ● INPUT REMOTE and REMOTE SYSTEM are enabled when REMOTE ENABLE is set to ON.