JVC XV-N50BK Instruction Manual - Page 36

Troubleshooting, Power, Operation, Picture, Audio, MP3/WMA

Page 36 highlights

Additional information Troubleshooting Power Power does not come on. \ Power plug is not inserted securely. Plug in securely. Operation "REGION CODE ERROR!" is shown on the TV screen. \ Region code of the inserted disc does not match the player. Check the region code of the disc printed on the disc jacket. Operation is not possible. \ Microcomputer malfunction due to lightning or static electricity. Turn off the power and unplug the power cord, then connect the power cord again. \ Moisture condensation caused by a sudden change of temperature or humidity. Turn off the power, then turn it on a few hours later. \ The disc does not allow the operation, or an unplayable disc is inserted. Check and replace the disc (see page 2). [LOCK] is displayed on the display window and the disc tray does not open. \ When you press 0 while pressing down 7 on the player in standby mode, the tray lock function is activated. The disc tray cannot be opened or closed in this status. To release this status, press 0 while pressing down 7 on the player in standby mode. Picture Picture is noisy. \ The player is connected to a VCR directly and the copyguard function is activated. Connect the player so that the picture signal flows directly to the TV. \ With some discs, the picture may be blurred when [PICTURE SOURCE] is set to [FILM] or [AUTO]. Set [PICTURE SOURCE] to [VIDEO (NORMAL)] or [VIDEO (ACTIVE)]. Picture is distorted when using COMPONENT VIDEO OUT or S-VIDEO output jack(s). \ Both the component connection and S-video connection are made. Disconnect the unused one. No picture is displayed on the TV screen or the screen is blurred or divided into two parts. \ The player is in the progressive scanning mode though it is connected to a TV via the VIDEO or S-VIDEO jack. Set the VIDEO SIGNAL SELECTOR on the rear panel to "480i," or set it to "REMOTE" and make the Progressive scanning mode inactive by using the VFP - PROGRESSIVE SCAN button (see page 4). Audio DVD VIDEO disc playback sound level is lower than TV broadcast sound level. \ Set the [D.RANGE CONTROL] preference to [TV MODE] (see page 28). Analog audio output is distorted. \ Set the [OUTPUT LEVEL] preference to [LOW] (see page 28). MP3/WMA No sound comes out. \ MP3/WMA disc is recorded with the "packet writing (UDF format)." It cannot be played. Files (tracks) are not played in the recorded order. \ This player plays the files in the alphabetic order. So, the playback order can vary. WMA files cannot be played back. \ The file is copy protected. \ The fils is recorded with a bit rate under 48 kbpos. The player does not support such WMA files. Additional information 34

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41

Additional information
34
Additional
information
Troubleshooting
Power
Power does not come on.
\
Power plug is not inserted securely. Plug in securely.
Operation
“REGION CODE ERROR!” is shown on the TV screen.
\
Region code of the inserted disc does not match the player.
Check the region code of the disc printed on the disc jacket.
Operation is not possible.
\
Microcomputer malfunction due to lightning or static electricity.
Turn off the power and unplug the power cord, then connect
the power cord again.
\
Moisture condensation caused by a sudden change of
temperature or humidity. Turn off the power, then turn it on a
few hours later.
\
The disc does not allow the operation, or an unplayable disc is
inserted. Check and replace the disc (see page 2).
[LOCK] is displayed on the display window and the disc tray
does not open.
\
When you press
0
while pressing down
7
on the player in
standby mode, the tray lock function is activated. The disc tray
cannot be opened or closed in this status. To release this
status, press
0
while pressing down
7
on the player in
standby mode.
Picture
Picture is noisy.
\
The player is connected to a VCR directly and the copyguard
function is activated. Connect the player so that the picture
signal flows directly to the TV.
\
With some discs, the picture may be blurred when [PICTURE
SOURCE] is set to [FILM] or [AUTO]. Set [PICTURE
SOURCE] to [VIDEO (NORMAL)] or [VIDEO (ACTIVE)].
Picture is distorted when using COMPONENT VIDEO OUT or
S-VIDEO output jack(s).
\
Both the component connection and S-video connection are
made. Disconnect the unused one.
No picture is displayed on the TV screen or the screen is
blurred or divided into two parts.
\
The player is in the progressive scanning mode though it is
connected to a TV via the VIDEO or S-VIDEO jack. Set the
VIDEO SIGNAL SELECTOR on the rear panel to “480i,” or set
it to “REMOTE” and make the Progressive scanning mode
inactive by using the VFP - PROGRESSIVE SCAN button
(see page 4).
Audio
DVD VIDEO disc playback sound level is lower than TV
broadcast sound level.
\
Set the [D.RANGE CONTROL] preference to [TV MODE] (see
page 28).
Analog audio output is distorted.
\
Set the [OUTPUT LEVEL] preference to [LOW] (see page 28).
MP3/WMA
No sound comes out.
\
MP3/WMA disc is recorded with the “packet writing (UDF
format).” It cannot be played.
Files (tracks) are not played in the recorded order.
\
This player plays the files in the alphabetic order. So, the
playback order can vary.
WMA files cannot be played back.
\
The file is copy protected.
\
The fils is recorded with a bit rate under 48 kbpos. The player
does not support such WMA files.