Jenn-Air JFFCC72EHL Owners Manual - Page 6
Getting Started - model
View all Jenn-Air JFFCC72EHL manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 6 highlights
GETTING STARTED INSTALLATION CHECKLIST ✔ Electrical Power ■■ Once the filter is inserted, turn the filter clockwise 90° (1/4 turn) until it locks into the housing. ■■ Push water filter door closed to latch. WARNING ■■ Flush 3 gallons (11.4 L) of water through the water system to clear air from the water line and to keep the dispenser from dripping and/or avoiding decreased dispenser flow. NOTE: If the filter is not installed correctly, water may dispense at a lower flow rate and there will be slower ice production. Improper filter installation may also cause the water filter housing to leak. Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. ■■ Plug refrigerator into a grounded 3 prong outlet. ✔ Doors ■■ If doors need to be removed during installation, see the "Remove and Replace Doors" in the instructions. ■■ Check that handles are secure and installed according to the instructions. ■■ Doors seal completely. ■■ Refrigerator is level. (Remove base grille and adjust leveling feet so they are snug against the floor.) ■■ Doors are even across the top. (Use door alignment feature if necessary.) ■■ Base grille is properly attached to the refrigerator. ✔ Ice and Water System (on some models) ■■ Connect refrigerator to a cold water supply with 20-120 psi water pressure, as specified in the instructions. ■■ Make sure the household water supply is connected and turned on. ■■ Check that the water supply line behind refrigerator is not kinked. ■■ Only use recommended water supply tubing, copper, or PEX, as specified in the instructions. ■■ Install water filter according to the instructions. ■■ Flush water system with 3 gallons (11.4 L) of water, as specified in the instructions. ■■ Check for water leaks at all connections. ■■ Turn on ice maker if refrigerator is connected to water supply. (If not connected to water supply, turn off ice maker.) ✔ Final Checks ■■ Install air filter according to instructions in corresponding packaging. ■■ Remove all shipping material. ■■ Set temperature controls to the recommended setting. ■■ Save instructions and other literature. ■■ Send in Registration Card or register your product online. WATER FILTER INSTALLATION ■■ Locate the water filter compartment in the lower left-hand side of the refrigerator compartment. Push on the right side of the filter door to open. ■■ Align the arrow on the water filter cap with the cutout notch in the filter housing and insert filter. DOOR ALIGNMENT Tools Required Depending on the width of the door opening, the following tools may be required to remove, replace, and align the refrigerator doors. Tools Needed: ■■ 1/4" hex nut driver - base grille, freezer drawer screws, and brake/leveling feet Tools Provided: ■■ 1/8" hex key - handle setscrews and door alignment Door alignment tool instructions Features: ■■ Creates an even horizontal gap between the refrigerator doors. ■■ Solves door alignment issues during installation and improves door seal. Align Refrigerator Doors ✔ If doors are uneven: ■■ Ensure the refrigerator is level. ■■ Keeping both refrigerator doors closed, pull out the freezer drawer. Locate the bottom hinge pin of the right-hand refrigerator door. The alignment screw is inside the bottom hinge pin. ■■ Insert the short end of the 1/8" hex-key wrench (packed with the Door Handle Installation Instructions) into the bottom hinge pin until it is fully engaged in the alignment screw. To raise the refrigerator door, turn the hex key to the right. To lower the door, turn the hex key to the left. 6