Jensen POWER 760 Operation Manual - Page 4
Features and Specifications - 4 channel amp
UPC - 857203635979
View all Jensen POWER 760 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 4 highlights
POWER Amplifiers Features and Specifications Your new Jensen Power mobile stereo power amplifier is the amplifier of choice for the high demands of auto sound reproduction. With its deep-bass reproduction and plenty of reserve power, low harmonic distortion and neutral reproduction, the Power series of amplifiers takes Mobile Hi-Fi to new heights. Like all Jensen products, when it comes to accurate sound reproduction the Power series takes a back seat to no one. Jensen will bring your Hi-Fi experience to new heights with the following features: • MOSFET Power Supply • High Current Bi-Polar Output Transistors • Optimized Class B Design Minimizes Distortion and Reduces Idle Current • Easily Drives 2-Ohm Loads • Pass-Thru RCA's • Variable Bass EQ 0 - 12dB @ 45 Hz • 12dB / Octave Low Pass and High Pass filters • Variable Input Level 400mV - 5V • Short Circuit, DC-offset and Thermal Overload Protection Circuitry • Diagnostic LED's - Green: Power, Red: Standby / Fault Power 400 / 760 / 880 / 920 • Low Pass Filter 40 - 300 Hz • High Pass Filter 40 - 300 Hz • High Pass / Low Pass / Full Range Selector Switch • Stereo / Mono Mode Switch (Power 400 and 880 only) • 2/ 3 / 4 Channel Mode Switch (Power 760 and 920 only)) Power 900 / 1050 • Mono Subwoofer Amp • Low Pass Filter 40 - 240 Hz (Power 900) • Low Pass Filter 40 - 150 Hz (Power 1050) • Subsonic Filter 10 - 40 Hz, 12dB / octave (Power 900) • Subsonic Filter 15 - 55 Hz, 12dB / octave (Power 1050) • Remote Input Level Control (Remote Bass Control) w/ 5 Meter Interface Cable Specifications Power 400 / 760 / 880 / 920 • Load Impedance: 2 / 4-Ohm • Signal to Noise @ 1 kHz: >100dB (rated power) • Channel Separation @ 1 kHz: >60dB • Frequency Response: 5-60 kHz, -3dB • Input Impedance: 20 kHz, nominal • THD+N @ 5 Watts: 0.02%, 1 kHz, 14.4VDC Power 900 / 1050 • Signal to Noise @ 120 Hz: >100dB (Rated Power) • Channel Separation Not Applicable • THD+N @ 5 Watts: 0.02%, 125 Hz, 14.4VDC Power Output RMS Power Output @ 2% THD+N, 1kHz, 14.4VDC Power 400 • 75 x 2 Watts, 4-Ohm • 100 x 2 Watts, 2-Ohm • 200 x 1 Watts, 4-Ohm Bridged Power 760 • 75 x 4 Watts, 4-Ohm • 100 x 4 Watts, 2-Ohm • 190 x 2 Watts, 4-Ohm Bridged Stereo Power 880 • 135 x 2 Watts, 4-Ohm • 220 x 2 Watts, 2-Ohm • 440 x 1 Watts, 4-Ohm Bridged Power 900 • 300 x 1 Watts, 4-Ohm • 450 x 1 Watts, 2-Ohm Power 920 • 100 x 4 Watts, 4-Ohm • 140 x 4 Watts, 2-Ohm • 230 x 2 Watts, 4-Ohm Bridged Stereo Power 1050 • 350 x 1 Watts, 4-Ohm • 525 x 1 Watts, 2-Ohm Specifications subject to change without notice. 2