Kenmore 2029219 Use and Care Manual - Page 17

Press

Get Kenmore 2029219 - Canister Vacuum PDF manuals and user guides
UPC - 037988771004
View all Kenmore 2029219 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

AlwayfsollowallsafetpyrecautiownhsenperformimngaintenanocnethePower-Mate Electrical Shock Or Personal Injury Hazard. Disconnect electrical supply before performing maintenance to the vacuum cleaner. Failure to do so could result in electrical shock or personal injury from vacuum cleaner suddenly starting,, i BELT CHANGING AND AGITATOR CLEANING f__ TO REMOVE BELT TO REPLACE BELT ! lolnstallnew _ _ "-..._ 3. -PJrnPowerMate up..Press handle release pedal and lower the swivel Lift rear and side latches up down 2P.owUenrs-cMreawte twcoov(e2r) motor drive, then over belt path,, __ "_'___.J_" __#._ _._M_t_r ,, -- \ Pozh Agitator End Cap NOTE: See PARTS AND FEATURES for Belt number 2oPlace agitator assembly back into Power-Mate 4. To remove cover, grasp the sides and pull out &Line up front [/(___'_L_ of cover and base, Rest cover on front edge ofbase as shown, Cover Base and remove worn belt End Cap 6, Check and clean end cap areas., See TO CLEAN AGITATOR section and AGITATOR ASSEMBLY illustration for picture of complete agitator assembly, __ 4. Rotate cover bacPr,ess __.__# "ii_,_ cover firmly until L_.[_Lside < ) ii tohos and rear snanpto "_ide Latch RY_ Latches place, Make sure there is no gap between the cover and base, 5. Turn Power-Mate upside down and replace two (2) cover screws, 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
Always
followallsafety
precautions
whenperforming
maintenance
onthePower-Mate
Electrical
Shock Or Personal
Injury
Hazard.
Disconnect
electrical
supply
before
performing
maintenance
to the vacuum
cleaner.
Failure
to do so could
result in electrical
shock
or personal
injury
from vacuum
cleaner
suddenly
starting,,
i
BELT
CHANGING
AND AGITATOR
CLEANING
f__
TO
REMOVE
BELT
TO
REPLACE
BELT
!
lolnstallnew
_
_
motor drive,
__
"_"_.,"_,.._._'-_((
_
....................
down
then over
"_'___.J_"
2.
Unscrew two (2)
belt path,,
__#._
_._M_t_r
Power-Mate
cover
"-..._
,,
--
\
Pozh
Agitator
End
Cap
4. To remove cover,
grasp the sides and
pull out
3.
-PJrnPower-
Mate
up..Press handle
release pedal and
lower the swivel
Lift rear and side
latches up
End
Cap
and remove
worn belt
6, Check and clean end cap areas., See TO
CLEAN AGITATOR section and AGITATOR
ASSEMBLY
illustration for picture of
complete agitator assembly,
NOTE: See
PARTS AND
FEATURES for
Belt number
2o
Place agitator
assembly back
into Power-Mate
&Line
up front
[/(___'_L_
of cover and
base,
Rest
cover on front
edge ofbase
as
shown,
Cover
Base
__
4. Rotate cover
bac ,
Press
__.__#
"ii_,_
cover firmly until
_'_"_'>'_-_"'_'_---L_.[_Lside
and rear
< )
ii tohos
snap
nto
"_ide
RY_
place,
Latch
Latches
Make sure there is no gap between the
cover and base,
5.
Turn Power-Mate upside down and
replace two (2) cover screws,
17