Kenmore 2803 Use and Care Guide - Page 8

Installation, Instructions

Get Kenmore 2803 - Elite Oasis Agitator 4.5 cu. Ft. Capacity Washer PDF manuals and user guides View all Kenmore 2803 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

INSTALLATION INSTRUCTIONS 6. Remove tape from lid. Open lid and remove foam packing ring from washer tub. Keep foam packing ring in case you need to move the washer in the future. Excessive Weight Hazard Use two or more people to move and install washer. Failure to do so can result in back or other injury. NOTE: To avoid floor damage during installation, set the washer onto cardboard before moving across floor. IMPORTANT: • Be sure the foam shipping base has been removed from the bottom of the washer as directed in the Unpacking Instructions. • If foam shipping base has not been removed, be sure lid is secured with tape before laying washer on its back. • Removing the foam shipping base is necessary for proper operation. 1, Place cardboard supports from shipping carton on floor behind washer for support. 2, Secure the lid with tape. 3, Using 2 or more people, tip the washer onto its hack and place on cardboard supports. 4, Remove foam shipping base. Proper connection of the drain hose protects your floors from damage due to water leakage. Read and follow these instructions. The drain hose is connected to your washer and is stored inside the washer cabinet. 5. Set washer upright. Remove drain hose from washer cabinet Pull the corrugated drain hose out of the washer by first grabbing the pull tie. Continue to pull the hose until the end emerges. Do not force excess drain hose back into the rear of the washer.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
INSTALLATION
INSTRUCTIONS
Excessive
Weight
Hazard
Use two or more people to move and install washer.
Failure to do so can result in back or other injury.
NOTE:
To avoid floor damage
during installation,
set the washer
onto cardboard
before moving across floor.
IMPORTANT:
•
Be sure the foam shipping
base has been removed
from the
bottom
of the washer as directed
in the Unpacking
Instructions.
•
If foam shipping
base has not been removed,
be sure lid is
secured with
tape before
laying washer
on its back.
•
Removing
the foam shipping
base is necessary for proper
operation.
1,
Place cardboard
supports
from shipping
carton on floor
behind
washer for support.
2,
Secure the lid with tape.
3,
Using 2 or more people, tip the washer onto its hack and
place on cardboard
supports.
4,
Remove foam shipping
base.
6.
Remove tape from
lid. Open lid and remove foam
packing
ring from washer tub. Keep foam
packing
ring in case you
need to move the washer in the future.
Proper connection
of the drain hose protects
your floors from
damage
due to water leakage. Read and follow these
instructions.
The drain hose is connected
to your washer
and is stored inside
the washer cabinet.
Remove
drain
hose
from
washer
cabinet
Pull the corrugated
drain hose out of the washer
by first grabbing
the pull tie. Continue
to pull the hose until the end emerges. Do
not force excess
drain hose back into the rear of the washer.
5.
Set washer upright.