Kenmore 7703 Use and Care Guide - Page 19

2.

Select the desired cycle and options.

3.

Press START. The dryer starts at the beginning

of the new

cycle.

NOTE: If you do not press Start within 5 minutes

of selecting

the

cycle, the dryer automatically

shuts off.

Changing

Modifiers

and

Options

after

pressing

Start

You can change a Modifier

or Option

anytime

before the selected

Modifier

or Option

begins.

1.

Press STOP once.

2.

Select the new Modifier

and/or

Options.

3.

Press START to continue

the cycle.

NOTE: If you happen to press STOP twice, the program

clears

and your dryer shuts down.

Restart the selection

process.

Changing

the

Preset

Dryness

Level

Settings

If

all your loads on all Auto Dry cycles

are consistently

not as dry

as you would

like, you may change the preset Dryness Level

settings to increase the dryness. This change will affect all of your

Auto Dry cycles.

Your Dryness Level settings

can be adjusted

to adapt to different

installations,

environmental

conditions

or personal

preference.

There are 3 drying

settings:

1 (factory

preset dryness

level),

2 (slightly

dryer clothes,

approximately

15% more drying time)

and 3 (much dryer clothes,

approximately

30%

more drying

time).

1.

The Dryness Level settings

cannot

be changed

while

the

dryer is running.

2.

Press and hold the Dryness Level button for 5 seconds.

The

dryer will beep, and "CF" will be displayed

for 1 second

followed

by the current

drying setting.

3.

To select a new drying setting,

press the Dryness Level key

again until the desired drying setting

is shown.

NOTE: While cycling through

the settings,

the current setting

will not flash,

but the other settings

will flash.

4.

Press START to save the drying setting.

5.

The drying

setting you selected

will become your new preset

drying setting

for all Auto Dry cycles.

The dryer rack was shipped

in the dryer

drum.

Use the dryer

rack for items that you do not want to tumble

dry,

such as sweaters.

Use Timed

Dry to select the desired time.

NOTE: Do not use Auto Dry Cycles

with the dryer rack.

To use

the

dryer rack:

Do not remove the lint screen.

1.

Open dryer door.

2.

Slide dryer

rack over the bottom

of the dryer

door opening.

Rest the back wire on the dryer back ledge.

Push down

on

the frame front to secure over lint screen.

3=

Place wet items

on top of the rack. Allow

space around

items

for air to circulate.

The rack does not move, but the drum will

rotate.

Make sure items do not hang over the edges or

between

rack grille.

4.

Close the door.

5.

Select TIMED

DRY and TIME ADJUST

MORE TIME or LESS

TIME. Refer to the following

table.

6.

Select the desired temperature

setting to match the fabrics

in

your load by pressing

TEMPERATURE.

Items containing

foam,

rubber or plastic

must be dried on a clothesline

or by

using an air cycle. Refer to the following

table.

7.

Start the dryer.

NOTE: Check the lint screen

and remove any lint accumulated

from items dried on the rack.

Suggested

Items for Rack

Cycle

Suggested

Drying

Setting

Time*

(Minutes)

Washable wool items

Low

20

(block to shape and lay flat

on rack)

Stuffed toys or pillows

Low

30

(cotton or polyester

fiber filling)

Stuffed toys

Air Dry

50

(foam rubber filled)

Galoshes

(rubber)

Air Dry

20

Foam rubber

pillows

Air Dry

50

Tennis shoes

Air Dry

20

*Reset

time as needed to complete

drying.

NOTE: You must remove rack for normal tumbling.

To remove the

dryer rack, lift it straight

up and out of the dryer.

19

Kenmore 7703 Use and Care Guide - Page 19

Modifiers, after, pressing, Preset, Dryness, Level, To use, dryer rack, Items for Rack, Cycle,

Page 19 highlights