Kenmore 9410 Installation Instructions - Page 1

Kenmore 9410 - 30 in. Electric Range Manual

Get Kenmore 9410 - 30 in. Electric Range PDF manuals and user guides View all Kenmore 9410 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 1 highlights

INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE. READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. INSTALLER. Clearances and Dimensions 1. Provide adequate clearances between the range and adjacent combustible surfaces. 2. Location--Check location where the range will be installed. Check for proper electrical supply, and the stability of the floor. 3. Dimensions that are shown must be used. Given dimensions provide minimum clearance. Contact surface must be solid and level. SIDE VIEW Centerline of range SidoevOf3r_ng:ight" __-_ ®o 1_ e_hraenrgied Maximum depth fa_ro_ab_nneto_Sp.e _25"--_ RANGE OVERALL DIMENSIONS i :ii! iii: 30" _ 0' clearance below cooking top and at rear of range. p- 30 253/4' outlet location are maximum, Dashed cubedarea shows where the electrical outlet must be installed for flush to the wall installation 44 5/8' _ Door Open _ 9 / ,,_....ak_> / Wall -_.._Edge 2-5/8" for models equipped "'" with warmer drawers" 3-1/2" for models equipped with storage drawers *30" MINIMUM CLEARANCE BETWEEN THE TOP OF THE COOKING SURFACE AND THE BOTTOM OF AN UNPROTECTED WOOD OR METAL CABINET; OR 24" MINIMUM WHEN BOTTOM OF WOOD OR METAL CABINET IS PROTECTED BY NOT LESS THAN 1/4" FLAME RETARDANT MILLBOARD COVERED WITH NOT LESS THAN NO. 28 MSG SHEET STEEL, 0.015" STAINLESS STEEL, 0.024" ALUMINUM OR 0.020" COPPER. O" CLEARANCE IS THE MINIMUM FOR THE REAR OF THE RANGE. FOLLOW ALL DIMENSION REQUIREMENTS PROVIDED ABOVE TO PREVENT PROPERTY DAMAGE, POTENTIAL FIRE HAZARD, AND INCORRECT COUNTERTOP AND CABINET CUTS. TO ELIMINATE THE RISK OF BURNS OR FIRE BY REACHING OVER HEATED SURFACE UNITS, CABINET STORAGE SPACE LOCATED ABOVE THE SURFACE UNITS SHOULD BE AVOIDED. IF CABINET STORAGE IS TO BE PROVIDED, THE RISK CAN BE REDUCED BY INSTALLING A RANGE HOOD THAT PROJECTS HORIZONTALLY A MINIMUM OF 5" BEYOND THE BOTTOM OF THE CABINETS. PIN 316259200 (0104) 1 Fran_ais- Pages7-12 Espa5ol- Pbginas 13-18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
INSTALLATION
AND
SERVICE
MUST
BE
PERFORMED
BY A QUALIFIED
INSTALLER.
IMPORTANT:
SAVE
FOR
LOCAL
ELECTRICAL
INSPECTOR'S
USE.
READ
AND
SAVE
THESE
INSTRUCTIONS
FOR
FUTURE
REFERENCE.
Clearances
and Dimensions
1.
Provide adequate clearances between the range and adjacent combustible surfaces.
2.
Location--Check
location where the range will be installed. Check for proper electrical supply, and the stability
of the floor.
3.
Dimensions that are shown must be used. Given dimensions provide minimum clearance. Contact surface must
be solid and level.
SidoevOf3r_ng:ight"
__-_
®o
1_
e_hraenrgied
e
SIDE
VIEW
Maximum depth
fa_ro_ab_nne_Se
top.
_25"--_
i
:ii! iii:
i
30"
_
0' clearance below
cooking
top
and
at
rear of range.
RANGE
OVERALL
DIMENSIONS
253/4'
p-
30
44
5/8'
_
Door
Open
_
9
/
,,_
....
ak_>
Centerline
of
range
outlet
location
are maximum,
Dashed
cubed
area
shows where
the
electrical
outlet must be
installed
for
flush to
the wall installation
/
Wall
-_.._Edge
2-5/8"
for models equipped
"'"
with
warmer drawers"
3-1/2" for
models equipped
with
storage
drawers
*30"
MINIMUM
CLEARANCE
BETWEEN
THE TOP
OF THE COOKING
SURFACE
AND THE
BOTTOM
OF AN
UNPROTECTED WOOD OR METAL CABINET; OR 24" MINIMUM WHEN BOTTOM OF WOOD OR METAL CABINET IS
PROTECTED BY NOT LESS THAN 1/4" FLAME RETARDANT MILLBOARD COVERED WITH NOT LESS THAN NO. 28
MSG SHEET STEEL, 0.015" STAINLESS STEEL, 0.024" ALUMINUM
OR 0.020" COPPER. O" CLEARANCE
IS THE
MINIMUM
FOR THE REAR OF THE RANGE. FOLLOW ALL DIMENSION REQUIREMENTS
PROVIDED ABOVE TO
PREVENT PROPERTY DAMAGE, POTENTIAL FIRE HAZARD, AND INCORRECT COUNTERTOP AND CABINET CUTS.
TO ELIMINATE THE RISK OF BURNS OR FIRE BY REACHING OVER HEATED SURFACE UNITS, CABINET STORAGE
SPACE
LOCATED
ABOVE
THE SURFACE
UNITS
SHOULD
BE AVOIDED.
IF CABINET
STORAGE
IS TO
BE
PROVIDED, THE RISK CAN BE REDUCED
BY
INSTALLING
A RANGE
HOOD THAT PROJECTS HORIZONTALLY A
MINIMUM OF 5" BEYOND THE BOTTOM OF THE CABINETS.
Fran_ais-
Pages7-12
Espa5ol- Pbginas 13-18
PIN 316259200
(0104)
1