Kenwood DDX1035 Operation Manual 2 - Page 34

Accessories/Installation Procedure

Get Kenwood DDX1035 PDF manuals and user guides View all Kenwood DDX1035 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

Accessories/Installation Procedure Accessories 1 *1 6 *1 ..........1 ..........6 (M5x6mm) 2 *1 7 *1 ..........1 ..........6 (M5x7mm) 3 *1 DDX1035/DDX1035M only. *2 DDX155 only. ..........1 (2m) 4 ..........1 5 *2 ..........2 Installation Procedure 1 To prevent a short circuit, remove the key from the ignition and disconnect the · battery. 2 Make the proper input and output wire connections for each unit. 3 Connect the speaker wires of the wiring harness. (Accessory 2 ) 4 Connect the wiring harness wires in the following order: ground, battery, ignition. (Accessory 1 ) 5 Connect the wiring harness connector to the unit. 6 Install the unit in your car. 7 Reconnect the · battery. 8 Press the reset button. 9 Perform the Initial Setup. WARNING • If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box. • Do not cut out the fuse from the ignition wire (red) and the battery wire (yellow). The power supply must be connected to the wires via the fuse. ¤ • Mounting and wiring this product requires skills and experience. For best safety, leave the mounting and wiring work to professionals. • Make sure to ground the unit to a negative 12V DC power supply. • Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing. • Do not use your own screws. Use only the screws provided. If you use the wrong screws, you could damage the unit. • If your car's ignition does not have an ACC position, connect the ignition wires to a power source that can be turned on and off with the ignition key. If you connect the ignition wire to a power source with a constant voltage supply, such as with battery wires, the battery may be drained. • If the fuse blows, first make sure the wires are not touching to cause a short circuit, then replace the old fuse with one with the same rating. • Insulate unconnected wires with vinyl tape or other similar material. To prevent a short circuit, do not remove the caps on the ends of the unconnected wires or the terminals. 34 English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
34
English
Accessories/Installation Procedure
Accessories
1
*
1
..........
1
2
*
1
..........
1
3
..........
1
(2m)
4
..........
1
5
*
2
..........
2
6
*
1
..........
6
(M5x6mm)
7
*
1
..........
6
(M5x7mm)
*
1
DDX1035/DDX1035M
only.
*
2
DDX155 only.
Installation Procedure
1
To prevent a short circuit, remove the key
from the ignition and disconnect the
·
battery.
2
Make the proper input and output wire
connections for each unit.
3
Connect the speaker wires of the wiring
harness. (Accessory
2
)
4
Connect the wiring harness wires in the
following order: ground, battery, ignition.
(Accessory
1
)
5
Connect the wiring harness connector to
the unit.
6
Install the unit in your car.
7
Reconnect the
·
battery.
8
Press the reset button.
9
Perform the Initial Setup.
WARNING
• If you connect the ignition wire (red) and
the battery wire (yellow) to the car chassis
(ground), you may cause a short circuit,
that in turn may start a fire. Always connect
those wires to the power source running
through the fuse box.
• Do not cut out the fuse from the ignition
wire (red) and the battery wire (yellow). The
power supply must be connected to the
wires via the fuse.
¤
• Mounting and wiring this product requires
skills and experience. For best safety,
leave the mounting and wiring work to
professionals.
• Make sure to ground the unit to a negative
12V DC power supply.
• Do not install the unit in a spot exposed
to direct sunlight or excessive heat or
humidity. Also avoid places with too much
dust or the possibility of water splashing.
• Do not use your own screws. Use only
the screws provided. If you use the wrong
screws, you could damage the unit.
• If your car’s ignition does not have an ACC
position, connect the ignition wires to a
power source that can be turned on and
off with the ignition key. If you connect
the ignition wire to a power source with
a constant voltage supply, such as with
battery wires, the battery may be drained.
• If the fuse blows, first make sure the wires
are not touching to cause a short circuit,
then replace the old fuse with one with the
same rating.
• Insulate unconnected wires with vinyl tape
or other similar material. To prevent a short
circuit, do not remove the caps on the ends
of the unconnected wires or the terminals.