Kenwood DDX6903S Instruction Manual - Page 86

Removing the unit Only for, DDX9903S/DDX9703S/DDX6903S, DDX6703S/DDX9716BTS

Get Kenwood DDX6903S PDF manuals and user guides View all Kenwood DDX6903S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 86 highlights

CONNECTION/INSTALLATION ❏❏Connecting the GPS antenna Connect the GPS antenna (7) to the GPS terminal. • To install the GPS antenna, fix the metal plate (8) firmly on the dashboard, then place the GPS antenna (7) on the metal plate (8). -- Clean the dashboard or other surface beforehand. -- Install the GPS antenna (7) inside of the car, as horizontally as possible to allow easy reception of the GPS satellite signals. -- You can bend the metal plate (8) to conform to a curved surface, if necessary. 7 8 7 • Depending on the type of car, reception of the GPS satellite signals might not be possible with an internal installation. • Install this GPS antenna in an area away from any antennas that are used with CB radios or satellite televisions. • The GPS antenna should be installed at a position at least 30 cm (12 inches) from mobile phone or other transmitting antennas. • The above types of communication may interfere with signals from the GPS satellite. • Painting the GPS antenna with (metallic) paint may cause reduced performance. Removing the unit (Only for DDX9903S/DDX9703S/DDX6903S/ DDX6703S/DDX9716BTS) ❏❏Removing the trim plate 1 Engage the catch pins on the extraction key (3) and remove the two locks on the lower part. Lower the frame and pull it forward. 2 2 Remove from the upper two catches. • The frame can be removed from the top side in the same manner. ❏❏Removing the unit 1 Remove the trim plate. (See the left column.) 2 Insert the two extraction keys (3), then pull them as illustrated so that the unit can be removed. 3 • Be careful to avoid injury from the catch pins on the extraction key. 3 86

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
86
CONNECTION/INSTALLATION
❏
Connecting the GPS antenna
Connect the GPS antenna (
7
) to the GPS terminal.
• To install the GPS antenna, fix the metal plate
(
8
) firmly on the dashboard, then place the GPS
antenna (
7
) on the metal plate (
8
).
–
Clean the dashboard or other surface
beforehand.
–
Install the GPS antenna (
7
) inside of the car, as
horizontally as possible to allow easy reception
of the GPS satellite signals.
–
You can bend the metal plate (
8
) to conform to
a curved surface, if necessary.
7
7
8
• Depending on the type of car, reception of the
GPS satellite signals might not be possible with an
internal installation.
• Install this GPS antenna in an area away from any
antennas that are used with CB radios or satellite
televisions.
• The GPS antenna should be installed at a position
at least 30 cm (12 inches) from mobile phone or
other transmitting antennas.
• The above types of communication may interfere
with signals from the GPS satellite.
• Painting the GPS antenna with (metallic) paint
may cause reduced performance.
Removing the unit (Only for
DDX9903S/DDX9703S/DDX6903S/
DDX6703S/DDX9716BTS)
❏
Removing the trim plate
1
Engage the catch pins on the extraction
key (
3
) and remove the two locks on the
lower part. Lower the frame and pull it
forward.
3
2
2
Remove from the upper two catches.
• The frame can be removed from the top side in
the same manner.
❏
Removing the unit
1
Remove the trim plate. (See the left
column.)
2
Insert the two extraction keys (
3
), then
pull them as illustrated so that the unit can
be removed.
3
• Be careful to avoid injury from the catch pins on
the extraction key.