Kenwood DNX6980 Quick Start Guide - Page 20

Installation Procedure, Accessories - connector wiring

Get Kenwood DNX6980 PDF manuals and user guides
UPC - 019048192707
View all Kenwood DNX6980 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

Accessories 1 9 ..........1 ..........6 2 0 ..........1 ..........1 3 ! ..........1 5 m..........1 4 @ ..........1 ..........1 5 # ..........2 3 m..........1 6 $ ..........1 7 3 m..........1 ..........1 8 ..........6 20 | Quick Start Guide Installation Procedure 1. To prevent a short circuit, remove the key from the ignition and disconnect the battery. 2. Make the proper input and output wire connections for each unit. 3. Connect the speaker wires of the wiring harness. 4. Connect the wiring harness wires in the following order: ground, battery, ignition. 5. Connect the wiring harness connector to the unit. 6. Install the unit in your car. 7. Reconnect the - battery. 8. Press the reset button. 9. Perform the Initial Setup. (Refer to the Instruction Manual.) 2WARNING • If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box. • Do not cut out the fuse from the ignition wire (red) and the battery wire (yellow). The power supply must be connected to the wires via the fuse. Acquiring GPS Signals The first time you turn on DNX9980HD, you must wait while the system acquires satellite signals for the first time. This process could take up to several minutes. Make sure your vehicle is outdoors in an open area away from tall buildings and trees for fastest acquisition. After the system acquires satellites for the first time, it will acquire satellites quickly each time thereafter. About the Front Panel When removing the product from the box or installing it, the front panel may be positioned at the angle shown in (Fig. 1). This is due to the characteristics of mechanism the product is equipped with. When the product is first powered on works properly, the front panel will automatically move into the position (initial setting angle)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
20
|
Quick Start Guide
Installation Procedure
Accessories
1
..........
1
2
..........
1
3
..........
1
4
..........
1
5
..........
2
6
..........
1
7
..........
1
8
..........
6
9
..........
6
0
..........
1
!
5 m
..........
1
@
..........
1
#
3 m
..........
1
$
3 m
..........
1
1. To prevent a short circuit, remove the key
from the ignition and disconnect the
-
battery.
2. Make the proper input and output wire
connections for each unit.
3. Connect the speaker wires of the wiring
harness.
4. Connect the wiring harness wires in the
following order: ground, battery, ignition.
5. Connect the wiring harness connector to
the unit.
6. Install the unit in your car.
7. Reconnect the
-
battery.
8. Press the reset button.
9. Perform the Initial Setup. (Refer to the
Instruction Manual.)
2
WARNING
• If you connect the ignition wire (red) and the
battery wire (yellow) to the car chassis (ground),
you may cause a short circuit, that in turn may
start a fire. Always connect those wires to the
power source running through the fuse box.
• Do not cut out the fuse from the ignition wire
(red) and the battery wire (yellow). The power
supply must be connected to the wires via the
fuse.
Acquiring GPS Signals
The first time you turn on DNX9980HD, you
must wait while the system acquires satellite
signals for the first time. This process could
take up to several minutes. Make sure your
vehicle is outdoors in an open area away from
tall buildings and trees for fastest acquisition.
After the system acquires satellites for the
first time, it will acquire satellites quickly each
time thereafter.
About the Front Panel
When removing the product from the
box or installing it, the front panel may be
positioned at the angle shown in (Fig. 1). This
is due to the characteristics of mechanism
the product is equipped with.
When the product is first powered on works
properly, the front panel will automatically
move into the position (initial setting angle)