Kenwood DNX6980 Quick Start Guide - Page 26

Installing the GPS Antenna, Installing the Push-To-Talk, Switch and the Microphone

Get Kenwood DNX6980 PDF manuals and user guides
UPC - 019048192707
View all Kenwood DNX6980 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Installing the GPS Antenna GPS antenna is installed inside of the car. It should be installed as horizontally as possible to allow easy reception of the GPS satellite signals. To mount the GPS antenna inside your vehicle: 1. Clean your dashboard or other surface. 2. Peel the backing off of the adhesive on the bottom of the metal plate (accessory @). 3. Press the metal plate (accessory @) down firmly on your dashboard or other mounting surface. You can bend the metal plate (accessory @) to conform to a curved surface, if necessary. 4. Place the GPS antenna (accessory !) on top of the metal plate (accessory @). Installing the Push-To-Talk Switch and the Microphone Unit 1. Check the installation position of the microphone (accessory #) and the PushTo-Talk switch (accessory $). 2. Remove oil and other dirt from the installation surface. 3. Install the microphone. 4. Wire the microphone cable up to the unit with it secured at several positions using tape or the like. Accessory # Accessory $ Accessory ! Accessory @ Fix a cable with a commercial item of tape. ¤ • Depending on the type of car, reception of the GPS satellite signals might not be possible with an inside installation. • The GPS antenna should be installed at a position that is spaced at least 12 inch (30 cm) from cellular phone or other transmitting antennas. Signals from the GPS satellite may be interfered with by these types of communication. • Painting the GPS antenna with (metallic) paint may cause a drop in performance. Peel the release coated paper of double-face adhesive tape to fix on the place shown above. Adjust the direction of the microphone to the driver. 26 | Quick Start Guide ⁄ Install the microphone as far away as possible from the cell-phone.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
26
|
Quick Start Guide
Installing the GPS Antenna
Installing the Push-To-Talk
Switch and the Microphone
Unit
GPS antenna is installed inside of the car. It
should be installed as horizontally as possible
to allow easy reception of the GPS satellite
signals.
To mount the GPS antenna inside your
vehicle:
1. Clean your dashboard or other surface.
2. Peel the backing off of the adhesive on the
bottom of the metal plate (accessory
@
).
3. Press the metal plate (accessory
@
)
down firmly on your dashboard or other
mounting surface. You can bend the
metal plate (accessory
@
) to conform to a
curved surface, if necessary.
4. Place the GPS antenna (accessory
!
) on
top of the metal plate (accessory
@
).
Accessory
!
Accessory
@
¤
• Depending on the type of car, reception of the
GPS satellite signals might not be possible with an
inside installation.
• The GPS antenna should be installed at a position
that is spaced at least 12 inch (30 cm) from cellular
phone or other transmitting antennas. Signals
from the GPS satellite may be interfered with by
these types of communication.
• Painting the GPS antenna with (metallic) paint
may cause a drop in performance.
1. Check the installation position of the
microphone (accessory
#
) and the Push-
To-Talk switch (accessory
$
).
2. Remove oil and other dirt from the
installation surface.
3. Install the microphone.
4. Wire the microphone cable up to the unit
with it secured at several positions using
tape or the like.
Fix a cable with a commercial item of
tape.
Peel the release coated paper of double-face
adhesive tape to fix on the place shown above.
Adjust the direction of the microphone to the
driver.
Accessory
#
Accessory
$
Install the microphone as far away as
possible from the cell-phone.
/