Kenwood DPX-5000BT Operation Manual 1 - Page 36

Installing the DAB antenna, Caution, Determine the antenna installation position, Part list

Get Kenwood DPX-5000BT PDF manuals and user guides View all Kenwood DPX-5000BT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

INSTALLATION / CONNECTION Installing the DAB antenna (for ) Connect the supplied DAB antenna to the DAB antenna jack. ( 31) Caution • The film antenna (F) is exclusively for use inside the vehicle. • Do not install at the following locations: - where it may block the driver's view. - where it may obstruct the operation of safety devices such as air bags. - on movable glass surfaces such as the rear hatch. - at side of vehicle (e.g. door, front quarter window). - on rear window. • Signal strength will weaken when installed at the following locations: - on IR reflecting glass or locations covered with mirror type glass film. - where it overlaps with genuine radio antenna (pattern). - where it overlaps with window heating wires. - on glass that blocks radio signals (e.g. IR reflecting glass, thermal insulation glass). • Poor reception may occur: - due to noise when windscreen wiper, air conditioner, or motor is turned on. - depending on the direction of the broadcast station with respect to the vehicle (antenna). • Thoroughly wipe oil and dirt from the pasting surface with the supplied cleaner (I). • Do not bend or damage the film antenna (F). • It may not be possible to install on certain vehicles. • Check the cable routing of the film antenna (F) and amplifier unit (G) before pasting. • Do not apply any glass cleaner after pasting the film antenna (F). Determine the antenna installation position • The direction of the film antenna (F) changes depending on whether the film antenna (F) is installed on the right side or left side. • Be sure to check the installation location of film antenna (F) before installing. Film antenna cannot be re-pasted. • Separate from other antennas by at least 100 mm. • Do not paste the amplifier unit (G) on the ceramic line (black part) around the front glass. Because there is not enough adhesion. Installing the antenna on the left side Installing the antenna on the right side Ceramic line (black part) 30 mm 150 mm (F) (G) Earth sheet* 150 mm Earth sheet* (G) 30 mm (F) * Paste the earth sheet of the amplifier unit (G) on the metal part of the front pillar. Part list for installation (H) Cable clamper (F) Film antenna (G) Amplifier unit (cable with booster, 3.5 m) (I) Cleaner 32

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
32
(F)
(F)
30 mm
150 mm
30 mm
150 mm
(G)
(G)
Installing the DAB antenna
(for
)
Connect the supplied DAB antenna to the DAB antenna jack. (
 
31
)
Caution
•
The film antenna
(F)
is exclusively for use inside the vehicle.
•
Do not install at the following locations:
–
where it may block the driver’s view.
–
where it may obstruct the operation of safety devices such as air
bags.
–
on movable glass surfaces such as the rear hatch.
–
at side of vehicle (e.g. door, front quarter window).
–
on rear window.
•
Signal strength will weaken when installed at the following
locations:
–
on IR reflecting glass or locations covered with mirror type glass
film.
–
where it overlaps with genuine radio antenna (pattern).
–
where it overlaps with window heating wires.
–
on glass that blocks radio signals (e.g. IR reflecting glass, thermal
insulation glass).
•
Poor reception may occur:
–
due to noise when windscreen wiper, air conditioner, or motor is
turned on.
–
depending on the direction of the broadcast station with respect
to the vehicle (antenna).
•
Thoroughly wipe oil and dirt from the pasting surface with the
supplied cleaner
(I)
.
•
Do not bend or damage the film antenna
(F)
.
•
It may not be possible to install on certain vehicles.
•
Check the cable routing of the film antenna
(F)
and amplifier unit
(G)
before pasting.
•
Do not apply any glass cleaner after pasting the film antenna
(F)
.
Determine the antenna installation position
•
The direction of the film antenna
(F)
changes depending on whether the film antenna
(F)
is installed on the
right side or left side.
•
Be sure to check the installation location of film antenna
(F)
before installing. Film antenna cannot be re-pasted.
•
Separate from other antennas by at least 100 mm.
•
Do not paste the amplifier unit
(G)
on the ceramic line (black part) around the front glass. Because there is not
enough adhesion.
Installing the antenna on the left side
Installing the antenna on the right side
Ceramic line (black part)
Earth sheet*
Earth sheet*
*
Paste the earth sheet of the amplifier unit
(G)
on the metal part of the front pillar.
Part list for installation
(F)
Film antenna
(I)
Cleaner
(H)
Cable clamper
(G)
Amplifier unit
(cable with booster, 3.5 m)
INSTALLATION / CONNECTION