Kenwood DPX-5100BT Instruction Manual 2 - Page 26

Learning Steering Remote Control - harness

Get Kenwood DPX-5100BT PDF manuals and user guides View all Kenwood DPX-5100BT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

LEARNING STEERING REMOTE CONTROL (for ) You can control the unit with the steering remote control keys on your vehicle. After connection, you can configure the control keys according to your preference. • You can only make this configuration if your vehicle is equipped with the electrical steering remote control. • If the steering remote control in your car is not compatible, configuration may not be completed and an error message may appear. ( 29) Make the connection Steering remote cable (supplied) Gray/red Learning steering remote input terminal Rear panel Bright green/red Purple/red Connect to your vehicle's steering remote harness. Contact your KENWOOD dealer for details. Configure the control keys 1 Press repeatedly to enter STANDBY. 2 Press the volume knob to enter [FUNCTION]. 3 Turn the volume knob to select [SYSTEM], then press the knob. 4 Turn the volume knob to select [USER S.REMO], then press the knob. 5 Turn the volume knob to select [SET KEY], then press the knob. A key list of 16 assignable keys appears. • K## NONE: No function has been assigned. 6 Turn the volume knob to select any key from the key list to assign the function, then press the knob. "PRESS KEY TO ASSIGN K##" appears. 7 Press and hold any control keys on your steering remote control which you want to assign. A list of key functions will appear on the display. NONE (default)/ATT/SEEK UP/SEEK DOWN/VOL UP/VOL DOWN/MODE/ ON HOOK/OFF HOOK/VOICE/ENTER 8 Turn the volume knob to select a function to assign, then press the knob. The selected key function is assigned to the steering remote control key you have selected in step 7. The display returns to the key list as on step 5. • K## (Function): When certain function has been assigned to a key. 9 Repeat steps 6, 7 and 8 to assign other control keys. 10 Press and hold to exit. To reassign the control keys 1 Press repeatedly to enter STANDBY. 2 Press the volume knob to enter [FUNCTION]. 3 Turn the volume knob to select [SYSTEM], then press the knob. 4 Turn the volume knob to select [USER S.REMO], then press the knob. 5 Turn the volume knob to select [RESET KEY], then press the knob. 6 Turn the volume knob to select [YES], then press the knob. All the control keys will be reset. Selecting [NO] will cancel the operation. When [FACTORY RESET] is set to [YES] ( 6), it will also reset the learning steering remote control. To return to the previous setting item, press . 26 ENGLISH

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
26
ENGLISH
LEARNING STEERING REMOTE CONTROL
(for
)
You can control the unit with the steering remote control keys on your
vehicle. After connection, you can configure the control keys according to
your preference.
• You can only make this configuration if your vehicle is equipped with
the electrical steering remote control.
• If the steering remote control in your car is not compatible,
configuration may not be completed and an error message may appear.
(
29)
Make the connection
Configure the control keys
1
Press
repeatedly to enter STANDBY.
2
Press the volume knob to enter
[FUNCTION]
.
3
Turn the volume knob to select
[SYSTEM]
, then press the knob.
4
Turn the volume knob to select
[USER S.REMO]
, then press the knob.
5
Turn the volume knob to select
[SET KEY]
, then press the knob.
A key list of 16 assignable keys appears.
•
K## NONE
: No function has been assigned.
6
Turn the volume knob to select any key from the key list to assign
the function, then press the knob.
“PRESS KEY TO ASSIGN K##” appears.
Rear panel
Learning steering
remote input terminal
Gray/red
Bright green/red
Purple/red
Steering remote
cable (supplied)
Connect to your
vehicle’s steering
remote harness.
Contact your
KENWOOD dealer
for details.
7
Press and hold any control keys on your steering remote control
which you want to assign.
A list of key functions will appear on the display.
NONE
(default)/
ATT
/
SEEK UP
/
SEEK DOWN
/
VOL UP
/
VOL DOWN
/
MODE
/
ON HOOK
/
OFF HOOK
/
VOICE
/
ENTER
8
Turn the volume knob to select a function to assign, then press the
knob.
The selected key function is assigned to the steering remote control
key you have selected in step 7.
The display returns to the key list as on step 5.
•
K## (Function)
: When certain function has been assigned to a key.
9
Repeat steps
6
,
7
and
8
to assign other control keys.
10
Press and hold
to exit.
To reassign the control keys
1
Press
repeatedly to enter STANDBY.
2
Press the volume knob to enter
[FUNCTION]
.
3
Turn the volume knob to select
[SYSTEM]
, then press the knob.
4
Turn the volume knob to select
[USER S.REMO]
, then press the knob.
5
Turn the volume knob to select
[RESET KEY]
, then press the knob.
6
Turn the volume knob to select
[YES]
, then press the knob.
All the control keys will be reset.
Selecting
[NO]
will cancel the operation.
When
[FACTORY RESET]
is set to
[YES]
(
6)
, it will also reset the learning
steering remote control.
To return to the previous setting item, press
.