Kenwood KAC9102D Instruction Manual - Page 5
Controls - kac remote
View all Kenwood KAC9102D manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 5 highlights
Controls z KAC-9152D/8152D |} ~ Remote controller (KAC-9152D/KAC-8152D only) "//34,%6%,D" &2%15%.#9(Z 8o8 KAC-9102D/8102D { | } ~ p q rs t NOTE The control panel locates under the front side cover. Remove the cover to access to its controls for adjustment. (See page 3) 1 Fuse (KAC-9152D/9102D: 30 A × 2) Fuse (KAC-8152D/8102D: 40 A × 1) NOTE If you can't find the specified capacity fuse at your store etc., consult your Kenwood dealer. 2 Battery terminal 3 Ground terminal 4 Power control terminal Controls the unit ON/OFF. NOTE Controls the unit power. Be sure to connect it with all the systems. 5 Speaker output terminals • KAC-9152D As this unit accepts speakers with a minimum impedance of 1 ohm, connect speakers with 1-ohm or higher impedance to these terminals. • KAC-9102D/8152D/8102D As this unit accepts speakers with a minimum impedance of 2 ohms, connect speakers with 2-ohms or higher impedance to these terminals. 2CAUTION The rated input of the speakers should be no less than the maximum output of the amplifier. Otherwise malfunction may result. 6 REMOTE terminal (KAC-9152D/8152D only) Connects the Remote cable. NOTE Use the Remote cable of the accessory. 7 Speaker level input terminals NOTE • The genuine-accessory car stereo shall have a maximum power output of no more than 40 W. • Do not connect the speaker output leads from a power amplifier (Optional) to the speaker level input terminals of this unit, for this may cause malfunction or damage. • Do not connect cables and leads to both RCA cable input jacks and the speaker level input terminals simultaneously, for this may cause malfunction or damage. • Connect the power control lead to a power supply which can be turned ON/OFF by the ignition key switch (ACC line). With this connection, shock noise may be generated when the power of the genuine-accessory car stereo is switched ON/OFF. 8 RCA cable ground lead terminal When using an RCA cable with a ground lead attached, connect the ground lead to this terminal. 9 LINE IN terminal u vw xy 0 LINE OUT terminal The signal that's input from the line input terminal is output. ! Power indicator When the power is turned on, the Power indicator lights. If the Power indicator does not light when the power is turned on, the protection function may be activated. Check whether there is any indication of trouble. (See page 2) @ BASS BOOST LEVEL control (KAC-9102D/8102D only) Sets the low frequency level to be compensated. # LPF(Low-Pass Filter) FREQUENCY control This control adjusts the frequency band output from this unit. $ ISF (infrasonic filter) switch Ultralow frequencies that cannot be reproduced even by a subwoofer speaker do not become sound but become unnecessary oscillations, which affect the sound by causing distortion, etc. Setting this switch to "15 Hz" or "25 Hz" cuts the frequencies below the respective frequency. This improves the reproduction performance of the speakers by eliminating unnecessary oscillations which will not become sound. % PHASE switch When this switch is set "180°" (Reverse) the speaker output phase is reversed. ^ INPUT SENSITIVITY control Set this control according to the pre-output level of the center unit connected with this unit, or to the maximum power output of the genuineaccessory car stereo. Use the diagram on the right as a guide. NOTE For the pre-output level or the maximum power output, refer to the in the instruction manual of the center unit. & BOOST LEVEL (Bass boost level) control (KAC-9152D/8152D only) Sets the level by which the low frequency range should be boosted. * FREQUENCY (Bass boost frequency) control (KAC-9152D/ 8152D only) Sets the center frequency around which the low frequency range should be boosted. English 5