Kenwood KDCX790 Instruction Manual - Page 35

Category and Channel Search, Direct Access Tuning, Selecting the Preset Band, Channel Preset Memory

Page 35 highlights

Category and Channel Search Selecting the channel and category you want to receive. 1 Enter Category and Channel Search mode Press the Control knob. 2 Select the Category Push the Control knob towards [FM] or [AM]. • It is the item when the category of Middle text display part is selected. 3 Select the Channel Push the Control knob towards [4] or [¢]. • You cannot Channel search until the category information is acquired. Cancelling Category and Channel Search mode Press the Control knob. Function of remote control Direct Access Tuning Entering the channel and tuning. 1 Enter Direct Access Tuning mode Press the [DIRECT] button on the remote control. 2 Enter the channel Press the number buttons. 3 Do Channel Search Push the Control knob towards [4] or [¢]. Cancelling Direct Access Tuning Press the [DIRECT] button on the remote control. • You cannot search for a channel number which is not broadcasting. (KTC-SR902/KTC-SR903: optional accessory) • If you cannot receive any signal in the input Channel due to bad conditions on radio wave or other such problems, "Acquiring Signal" appears. Selecting the Preset Band Push the Control knob toward [FM]. Each time you push the knob, the preset band alternates between the SR1, SR2, SR3 and SR4. Channel Preset Memory Putting the channel in the memory. 1 Select the preset band Push the Control knob toward [FM]. 2 Select the channel to put in the memory Push the Control knob towards [4] or [¢]. 3 Select the key function section Press the [NEXT] button. Repeatedly press the button until "[1]" - "[6]" are displayed above the [1] - [6] buttons. Refer to (page 9). 4 Put the channel in the memory Press the desired [1] - [6] button for at least 2 seconds. The preset number display blinks 1 time. On each band, you can put 1 channel in the memory on each [1] - [6] button. • Only the channel number is stored. Category information is not stored. • If you make no button operation for 10 seconds, the Direct Access Tuning mode is automatically canceled. • You can set up until Channel number 223. • If there is no signal in the input Channel, "No Channel" appears. (KTC-SR901: optional accessory) English | 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64

English
|
35
Category and Channel Search
Selecting the channel and category you want to
receive.
1
Enter Category and Channel Search mode
Press the Control knob.
2
Select the Category
Push the Control knob towards [FM] or [AM].
• It is the item when the category of Middle text display
part is selected.
3
Select the Channel
Push the Control knob towards [
4
] or
[
¢
].
You cannot Channel search until the category
information is acquired.
Cancelling Category and Channel Search
mode
Press the Control knob.
Function of remote control
Direct Access Tuning
Entering the channel and tuning.
1
Enter Direct Access Tuning mode
Press the [DIRECT] button on the remote
control.
2
Enter the channel
Press the number buttons.
3
Do Channel Search
Push the Control knob towards [
4
] or
[
¢
].
Cancelling Direct Access Tuning
Press the [DIRECT] button on the remote
control.
• If you make no button operation for 10 seconds, the
Direct Access Tuning mode is automatically canceled.
• You can set up until Channel number 223.
• If there is no signal in the input Channel, "No Channel"
appears. (KTC-SR901: optional accessory)
• You cannot search for a channel number which is not
broadcasting.
(KTC-SR902/KTC-SR903: optional accessory)
• If you cannot receive any signal in the input Channel
due to bad conditions on radio wave or other such
problems, "Acquiring Signal" appears.
Selecting the Preset Band
Push the Control knob toward [FM].
Each time you push the knob, the preset band
alternates between the SR1, SR2, SR3 and SR4.
Channel Preset Memory
Putting the channel in the memory.
1
Select the preset band
Push the Control knob toward [FM].
2
Select the channel to put in the memory
Push the Control knob towards [
4
] or
[
¢
].
3
Select the key function section
Press the [NEXT] button.
Repeatedly press the button until "[1]" — "[6]" are
displayed above the [1] — [6] buttons.
Refer to <Notes on Multi-function Key System>
(page 9).
4
Put the channel in the memory
Press the desired [1] — [6] button for at least
2 seconds.
The preset number display blinks 1 time.
On each band, you can put 1 channel in the
memory on each [1] — [6] button.
• Only the channel number is stored. Category
information is not stored.