Kenwood TH-F6A User Manual - Page 35

Selective Call, Dcs Code Id Scan

Get Kenwood TH-F6A PDF manuals and user guides View all Kenwood TH-F6A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

8 SELECTIVE CALL DCS CODE ID SCAN This function scans through all DCS codes to identify the incoming DCS code on the received signal. You may find this useful when you cannot recall the DCS code that the other persons in your group are using. 1 While in DCS mode, press [F], [TONE] (1 s) to start the DCS Code ID Scan function. • To reverse the scan direction, turn the Tuning control or press [ ]/ [ ]. • To quit the function, press [ ] or [PTT]. • When a DCS code is identified, the identified code appears and blinks. 2 Press [ ] or [MNU] to program the identified frequency in place of the current DCS code. Otherwise, press [ ] if you do not want to program the identified code. • Turn the Tuning control or press [ ]/ [ ] while the identified DCS code is blinking to resume scanning. Note: x Received signals are monitored through the speaker while scanning is in progress. x DCS Code ID Scan does not scan the code if a signal is not detected. x If the DCS function is activated for both the A and B-band, the scan speed may be slower. 30

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
8
SELECTIVE CALL
30
DCS CODE ID SCAN
This function scans through all DCS codes to identify
the incoming DCS code on the received signal.
You
may find this useful when you cannot recall the DCS
code that the other persons in your group are using.
1
While in DCS mode, press
[F]
,
[TONE] (1 s)
to
start the DCS Code ID Scan function.
•
To reverse the scan direction, turn the
Tuning
control or press
[
]
/
[
]
.
•
To quit the function, press
[
]
or
[PTT]
.
•
When a DCS code is identified, the identified
code appears and blinks.
2
Press
[
]
or
[MNU]
to program the identified
frequency in place of the current DCS code.
Otherwise, press
[
]
if you do not want to
program the identified code.
•
Turn the
Tuning
control or press
[
]
/
[
]
while
the identified DCS code is blinking to resume
scanning.
Note:
◆
Received signals are monitored through the speaker while
scanning is in progress.
◆
DCS Code ID Scan does not scan the code if a signal is not
detected.
◆
If the DCS function is activated for both the A and B-band, the
scan speed may be slower.