Kenwood TM-D710GA Instruction Manual 1 - Page 28

Selecting Dual Band Mode/ Single Band Mode, Selecting A Frequency Band

Get Kenwood TM-D710GA PDF manuals and user guides View all Kenwood TM-D710GA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

SELECTING DUAL BAND MODE/ SINGLE BAND MODE You can switch the transceiver between dual band operation and single band operation by pressing [BAND SEL] (1s) of your selected band. Dual band mode: Single band mode (band A only): Note: You can also turn the center partition bar display off {Menu No. 928}. SELECTING A FREQUENCY BAND You can change the default frequency band for bands A and B. 1 Select band A or B by pressing the [BAND SEL] control or [PF2]. 2 Press [F], [BAND SEL] of your selected band. • Each time you press [F], [BAND SEL], you cycle to the next frequency band. • The default setting of the [PF1] key also allows you to cycle to the next frequency band (TM-D710GE). • When masking a band, you are restricted to using only the selectable band. • When receiving 2 signals on the same band, the image interference, sensitivity, etc., Performance will decrease. • Band A: 118 >> 144 (default) >> 220 >> 300 >> 430/440 (MHz). • Band B: 144 >> 220 >> 300 >> 430/440 (default) >> 1200 (MHz). Note: TM-D710GE models use the 430 MHz band and TM-D710GA models use the 440 MHz band. 20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
20
SELECTING DUAL BAND MODE/ SINGLE BAND MODE
You can switch the transceiver between dual band operation and single band
operation by pressing
[BAND SEL] (1s)
of your selected band.
Dual band mode:
Single band mode (band A only):
Note:
You can also turn the center partition bar display off {Menu No. 928}.
SELECTING A FREQUENCY BAND
You can change the default frequency band for bands A and B.
1
Select band A or B by pressing the
[BAND SEL]
control or
[PF2]
.
2
Press
[F], [BAND SEL]
of your selected band.
•
Each time you press
[F]
,
[BAND SEL]
, you cycle to the next frequency band.
•
The default setting of the
[PF1]
key also allows you to cycle to the next frequency
band (TM-D710GE).
•
When masking a band, you are restricted to using only the selectable band.
•
When receiving 2 signals on the same band, the image interference, sensitivity, etc.,
Performance will decrease.
•
Band A:
118 >> 144 (default) >> 220 >> 300 >> 430/440 (MHz).
•
Band B:
144 >> 220 >> 300 >> 430/440 (default) >> 1200 (MHz).
Note:
TM-D710GE models use the 430 MHz band and TM-D710GA models use the 440 MHz
band.