Kenwood VR9070 Instruction Manual - Page 21

Preparing for surround sound If you selected "FRNT NML/THX" as the Front Speaker setting, 1 SURR NML/THX : Average size Surround Speakers are connected to the receiver. 2 SURR OFF : Surround Speaker setting mode to the receiver is OFF. • When the setting "SURR OFF" is selected, you may skip to step !. 9 Press the 5 key or MULTI # key again to accept the setting. • The Surround Back Speaker setting indication "SB" appears. 0 Use the MULTI CONTROL knob or MULTI %/fi keys to select appropriate Surround Back Speaker setting. If you selected "SURR LARGE" as the Surround Speaker setting, 1 SB NML/THXx1 : A single average size Surround Back Speaker is connected to the receiver. 2 SB NML/THXx2 : A pair of average size Surround Back Speak- ers are connected to the receiver. 3 SB LARGEx1 : A single large size Surround Back Speaker is connected to the receiver. 4 SB LARGEx2 : A pair of large size Surround Back Speak- ers are connected to the receiver. 5 SB OFF : Surround Back Speaker setting mode to the receiver is OFF. SP MUTE L C SW R A B CLIP LFE SL SB SR STEREO If you selected "SURR NML/THX" as the Surround Speaker setting, 1 SB NML/THXx1 : A single average size Surround Back Speaker is connected to the receiver. 2 SB NML/THXx2 : A pair of average size Surround Back Speak- ers are connected to the receiver. 3 SB OFF : Surround Back Speaker setting mode to the receiver is OFF. ! Press the 5 key or MULTI # key again to accept the setting. • The Subwoofer re-mix setting indication "SW RE-MIX" appears. @ Use the MULTI CONTROL knob or MULTI %/fi keys to select the appropriate Subwoofer re-mix setting. 1 SW RE-MIX ON : Subwoofer re-mix setting mode to the receiver is ON. 2 SW RE-MIX OFF : Subwoofer re-mix setting mode to the receiver is OFF. • If subwoofer is turned off or "FRNT NML/THX" is selected at the Front Speakers setting, subwoofer re-mix setting is not visible. # Press the SETUP key again to return to the main setup displays. 5 Select the CROSSOVER frequency. CROSSOVER function is to adjust the receiver's audio output characteristics with the speakers' characteristics which differs depending on the size of the speakers. You will be able to enjoy a more natural and dynamic sound experience even with small size speakers. 1 Press the 5/∞ keys or MULTI @/# keys to select the CROSSOVER and press the SETUP key. 2 Use the MULTI CONTROL knob or MULTI %/fi keys to select the CROSSOVER frequency. 1 FREQ. : 40Hz 2 FREQ. : 60Hz 3 FREQ. : 80Hz-THX 4 FREQ. : 100Hz 5 FREQ. : 120Hz 6 FREQ. : 150Hz • If you have THX certified speakers, select "FREQ. : 80Hz-THX". SP MUTE L R A B CLIP STEREO • CROSSOVER function will not be available when "LARGE" is selected for all the speakers and "SW RE-MIX OFF" is selected in step 4. 3 Press the SETUP key again to return to the main setup displays. 6 Adjust the speaker volume level. From your usual listening position, adjust the volume levels. The volume levels from each speaker should be the same. • The receiver enters the speaker volume level adjustment mode. • Indicators appear only for the channels of the speakers selected in step 4. Be aware that the TEST TONE is quite a loud sound (0dB). 1 Press the 5/∞ keys or MULTI @/# keys to select the TEST TONE. 2 Press the SETUP key for the following displays: 1 T.TONE AUTO 2 T.TONE MANUAL 3 The selection of AUTO/MANUAL TEST TONE is done by the MULTI CONTROL knob or MULTI %/fi keys. Press the SETUP key again to begin TEST TONE. Use the MULTI CONTROL knob or MULTI %/fi keys to adjust the volume level of the test tone output from the speaker channel to be adjusted. For AUTO selection, the test tone is heard from the speakers in the following sequence for 2 seconds each starting from the Front Left Speaker. LEFT SUBW CNTR SL RIGHT SBL SR SBR • If you have selected "SB NML/THXx1" or "SB LARGEx1", "SBR" and "SBL" are not appeared but "SB" is appeared on the Display. The channel indication blinks while the test tone is being output. SP MUTE L C SW R A B CLIP LFE SL SB SR • If the speaker setting selects are OFF, the speaker level settings are reset. For MANUAL selection, press the 5/∞ keys or MULTI @/# keys each time to select the speaker channel. 4 Press the SETUP key again. • The test tone is turned off and return to the main setup displays. Continued to next page. 21 EN