Kenwood XXV-02A Instruction Manual - Page 6

Amplifier Control System FAN VOLT TEMP CURR 150 100 70 50 200 LPF FREQUENCY(Hz) 100 1 100 1 70 50 150 2 3 4 200 (MIN)5 0.5 70 0.3 0.2(MAX) 50 150 2 3 4 200 (MIN)5 0.5 0.3 0.2(MAX) HPF INPUT HPF INPUT FREQUENCY(Hz) SENSITIVITY(V) FREQUENCY(Hz) SENSITIVITY(V) HPF OPERATION LPF OPERATION 0 0 -4 -4 -8 -8 -12 -12 -16 -16 -20 -20 30 50 100 200 400 1K (Hz) 30 50 100 200 400 1K (Hz) 200 Hz 150 Hz 100 Hz 70 Hz 50 Hz B ch FILTER HPF AMP CONT ON A ch ISF OPERATION HPF OPERATION ON MONO(Lch) ON MONO(Lch) OFF LPF OFF OFF STEREO OFF STEREO Indicator MENU 2 / 3 Display mode You can set up the display items as follows: 1 Enter Menu mode Press the [MENU] button. "VOLT"/"CURR"/"TEMP"/"FAN" is displayed. 2 Select a display item Press the [2] or [3] button. The display items are switched in the following sequence. Display "VOLT" "CURR" "TEMP" "FAN" Information Indicates the source voltage (V). Indicates the current consumption (A). Indicates the internal temperature (°F/°C). Indicates the rotation speed of the cooling fan in 3 steps: "FAST", "SLOW" or "OFF". 3 Exit Menu mode Press the [MENU] button for at least 1 second. NOTE When the internal temperature is -22°F/-30°C or less, "-22F"/"-30C" is displayed. Separate Amp Control The following explains how to control the sound of amplifier B using the Amplifier Control of the unit. 1 Enter Menu mode Press the [MENU] button. 2 Select the Menu item Press the [MENU] button. The setup items are displayed approximately 1 second first, then the set values are displayed. 3 Adjust the Menu item Press the [2] or [3] button. The setup items and set values are switched as follows. Display Range "VOLT"/"CURR"/"TEMP"/"FAN" "BASS" 60/80/100/200 (Hz) "BA G" B-15 - B+15 (dB) "BA Q" Q1.00/Q1.25/Q1.50/Q2.00 "EXT" ON/OFF "TREB" "TR G" "VOL" "TEMP" "DEFA" "AMP" 10/12/15/17 (kHz) T-15 - T+15 (dB) -20 - 0 (dB) FAHR (Fahrenheit) or CELS (Centigrade) 0 - 7 Adjustment Item For the operation method refer to Bass Center Frequency Bass level Bass Q Factor When the bass extend is set to ON, low frequency response is extended by 20%. Treble Center Frequency Treble level Volume offset The Fahrenheit or Centigrade temperature unit can be selected for the Display mode. For the operation method refer to The ID Number you have assigned is displayed. 4 Exit Menu mode Press the [MENU] button for at least 1 second. NOTE When you hold down the [3] button 3 or more seconds during ID number display ("AMP"), message "MEMO" is displayed and you can register the values you have set with the Amplifier Control. To call the Amplifier Control's values, hold down the [2] button 3 or more seconds during ID number display ("AMP"). Then, you can recall the value when message "LOAD" is displayed. Default Resets all values you have set to the initial (default) values. 1 Enter Menu mode Press the [MENU] button. 2 Select Default mode Press the [MENU] button. Select the "DEFA" display. 3 Resets the value to its default Press the [3] button for at least 2 seconds. Message "----" is displayed, and the value is initialized. 4 Exit Menu mode Press the [MENU] button for at least 1 second. NOTE Volume offset value can not be initialized. Display Demonstration The "VOLT"/"CURR"/"TEMP"/"FAN" items are displayed repeatedly. Press the [MENU] button for at least 2 seconds. The indicator flashes in the Demonstration mode. Canceling the Demonstration mode Press any button to cancel the Demonstration mode. 6 English