KitchenAid KBBL206ESS Installation Guide - Page 13

Stainless Steel and Overlay Series, Factory Panels and Kits, 91.4 cm] Models, Stainless Steel,

Get KitchenAid KBBL206ESS PDF manuals and user guides View all KitchenAid KBBL206ESS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

Stainless Steel and Overlay Series Factory Panels and Kits (36" [91.4 cm] Models) All factory parts are available through your KitchenAid dealer or by calling KitchenAid Parts and Accessories at 1-800-442-9991. In Canada, call 1-800-807-6777. Stainless Steel Series 72" (183 cm) Top Grille Panel Kit A 72" (183 cm) wide Top Grille Panel Kit is available. This kit allows 2 units (one left-hand swing and one right-hand) to be installed side by side with a single grille. Stainless Steel (Stainless Steel Series) #W10153554 Extended Door Handle Kits Use extended door handles when additional finger clearance is needed between the door handles and custom panel. Follow the kit instructions for installing the door handles. Matte Aluminum (Overlay Series) #4396718 Stainless Steel Series Custom Side Panels Custom side panels may be needed when not enough space is available to have cabinets on both sides of the refrigerator or when the refrigerator is placed at the end of a cabinet run. You may choose an Inset, Flush, or Recessed Inset panel installation. Refrigerator and Side Trim Dimensions The width and height of a side panel are determined by the type of installation you are planning. NOTES: ■ The dimensions shown are actual product dimensions and may not reflect the needed panel installation dimensions. ■ The side panel should be a minimum of ¹⁄₂" (1.27 cm) thick to avoid warping. ■ If the opening depth is 25" (63.5 cm) or more, you may want to install a support board on the rear wall. Refrigerator Side Trim 18.0 mm) ¹⁄₂" (12.2 mm) 13.9 mm) ⁵⁄₈" (15.7 mm) Inset Installation Dimensions 1. Measure the distance from point A (as shown) to the back wall. Add 5.6 mm) to this measurement to allow the side panel to fit into the trim. A 2. If the panel is more than ¹⁄₄" (6.35 mm) thick, rout the front edge to allow the side panel to fit into the trim. Flush Installation Dimensions 1. Measure the distance from point A (as shown) to the back wall. 24¹⁄₈" (61.3 cm) 23 60.3 cm) 23¹⁄₂" (59.7 cm) A 2. Attach the support board with a screw or adhesive that is compatible with aluminum and wood. Recessed Inset Installation Dimensions 1. Measure the distance from point A (as shown) to back wall. A 2. Rout the front edge of the support board or attach a ¹⁄₄" (6.35 mm) board to hold the panel in the cabinet side trim. 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
13
Stainless Steel and Overlay Series
Factory Panels and Kits
(36" [91.4 cm] Models)
All factory parts are available through your KitchenAid dealer or by
calling KitchenAid Parts and Accessories at
1-800-442-9991
. In
Canada, call
1-800-807-6777
.
Stainless Steel Series 72" (183 cm) Top Grille Panel Kit
A 72" (183 cm) wide Top Grille Panel Kit is available. This kit allows
2 units (one left-hand swing and one right-hand) to be installed
side by side with a single grille.
Extended Door Handle Kits
Use extended door handles when additional finger clearance is
needed between the door handles and custom panel. Follow the
kit instructions for installing the door handles.
Stainless Steel
Series Custom Side Panels
Custom side panels may be needed when not enough space is
available to have cabinets on both sides of the refrigerator or
when the refrigerator is placed at the end of a cabinet run. You
may choose an Inset, Flush, or Recessed Inset panel installation.
Refrigerator and Side Trim Dimensions
The width and height of a side panel are determined by the type of
installation you are planning.
NOTES:
■
The dimensions shown are actual product dimensions and
may not reflect the needed panel installation dimensions.
■
The side panel should be a minimum of
¹⁄₂
" (1.27 cm) thick
to avoid warping.
■
If the opening depth is 25" (63.5 cm) or more, you may
want to install a support board on the rear wall.
Refrigerator
Side Trim
Inset Installation Dimensions
1.
Measure the distance from point A (as shown) to the back
wall. Add
⁷⁄₃₂
" (5.6 mm) to this measurement to allow the side
panel to fit into the trim.
2.
If the panel is more than
¹⁄₄
" (6.35 mm) thick
,
rout the front
edge to allow the side panel to fit into the trim.
Flush Installation Dimensions
1.
Measure the distance from point A (as shown) to the back
wall.
2.
Attach the support board with a screw or adhesive that is
compatible with aluminum and wood.
Recessed Inset Installation Dimensions
1.
Measure the distance from point A
(as shown) to back wall.
2.
Rout the front edge of the support board or attach a
¹⁄₄
"
(6.35 mm) board to hold the panel in the cabinet side trim.
Stainless Steel (Stainless Steel Series)
#W10153554
Matte Aluminum (Overlay Series)
#4396718
24
¹⁄₈
"
(61.3 cm)
23
¹⁄₂
"
(59.7 cm)
23
¹¹⁄₁₆
"
(60.3 cm)
⁹⁄₁₆
"
(13.9 mm)
¹⁄₂
"
(12.2 mm)
¹¹⁄₁₆
"
(18.0 mm)
⁵⁄₈
"
(15.7 mm)
A
A
A