KitchenAid KBBL206ESS Installation Guide - Page 14

Overlay Series Custom Side Panels

Get KitchenAid KBBL206ESS PDF manuals and user guides View all KitchenAid KBBL206ESS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

Overlay Series Custom Side Panels Custom side panels may be needed when not enough space is available to have cabinets on both sides of the refrigerator or when the refrigerator is placed and the end of a cabinet run. You may choose an Inset or Recessed Inset panel installation. Refrigerator and Side Trim Dimensions Side Trim (36" [91.4 cm] Models) ³⁄₈" (9.7 mm) The width and height of a side panel are determined by the type of installation you are planning. NOTES: ■ The dimensions shown are actual product dimensions and may not reflect the needed installation dimensions. ■ The side panel should be a minimum of ¹⁄₂" (1.3 cm) thick to avoid warping. ■ If the opening depth is 25" (63.5 cm) or more, you may want to install a support board on the rear wall. Refrigerator (36" [91.4 cm] Models) 1.5 mm) Overlay 2.38 mm) 4.5 mm) 23 60.16 cm) Side Trim (42" [106.7 cm] Models) ³⁄₈" (9.7 mm) 4.5 mm) Refrigerator (42" [106.7 cm] Models) Overlay 23³⁄₈" (59.40 cm) 14 1.5 mm) ¹⁄₈" (3.2 mm) Inset Installation Dimensions 36" [91.4 cm] Models 1. Measure the distance from point A (as shown) to the back wall. Add 0.8 mm) to this measurement to allow the side panel to fit into the trim. A 2. If the panel is more than ³⁄₈" (9.5 mm) thick, rout the front edge to allow the side panel to fit into the trim

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
14
Overlay Series Custom Side Panels
Custom side panels may be needed when not enough space is
available to have cabinets on both sides of the refrigerator or
when the refrigerator is placed and the end of a cabinet run. You
may choose an Inset or Recessed Inset panel installation.
Refrigerator and Side Trim Dimensions
The width and height of a side panel are determined by the type of
installation you are planning.
NOTES:
■
The dimensions shown are actual product dimensions and
may not reflect the needed installation dimensions.
■
The side panel should be a minimum of
¹⁄₂
" (1.3 cm) thick
to avoid warping.
■
If the opening depth is 25" (63.5 cm) or more, you may
want to install a support board on the rear wall.
Refrigerator (36" [91.4 cm] Models)
Refrigerator (42" [106.7 cm] Models)
Side Trim (36" [91.4 cm] Models)
Side Trim (42" [106.7 cm] Models)
Inset Installation Dimensions
36" [91.4 cm] Models
1.
Measure the distance from point A (as shown) to the back
wall. Add
¹⁄₃₂
" (0.8 mm) to this measurement to allow the side
panel to fit into the trim.
2.
If the panel is more than
³⁄₈
" (9.5 mm) thick,
rout the front edge
to allow the side panel to fit into the trim
23
¹¹⁄₁₆
"
(60.16 cm)
Overlay
23
³⁄₈
"
(59.40 cm)
Overlay
³⁄₁₆
"
(4.5 mm)
³⁄₈
"
(9.7 mm)
¹⁄₁₆
"
(1.5 mm)
³⁄₃₂
"
(2.38 mm)
³⁄₁₆
"
(4.5 mm)
³⁄₈
"
(9.7 mm)
¹⁄₁₆
"
(1.5 mm)
¹⁄₈
"
(3.2 mm)
A