KitchenAid KBSN702MPA Owners Manual - Page 17

INSTALLATION INSTRUCTIONS, Unpack the Refrigerator

Get KitchenAid KBSN702MPA PDF manuals and user guides View all KitchenAid KBSN702MPA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Side Trim 11/16" (18.0 mm) 1/2" (12.2 mm) INSTALLATION INSTRUCTIONS Unpack the Refrigerator WARNING 9/16" (13.9 mm) 5/8" (15.7 mm) Inset Installation Dimensions 1. Measure the distance from point A (as shown) to the back wall. Add 1/16" (1.6 mm) to this measurement to allow the side panel to fit into the trim. 2. If the panel is more than 11/32" (8.7 mm) thick, route the front edge to allow the side panel to fit into the trim. A Recessed Inset Installation Dimensions 1. Measure the distance from point A (as shown) to back wall. 2. Route the front edge of the support board or attach a 3/8" (9.5 mm) board to hold the panel in the cabinet side trim. A Tip Over Hazard Refrigerator is top heavy and tips easily when not completely installed. Keep doors taped closed until refrigerator is completely installed. Use two or more people to move and install refrigerator. Failure to do so can result in death or serious injury. IMPORTANT: � Do not remove the film covering until the refrigerator is in its operating location. � All four leveling legs must contact the floor to support and stabilize the full weight of the refrigerator. � Keep the cardboard shipping piece or plywood under the refrigerator until it is installed in the operating location. 1. Remove and save the literature package bag taped to the side of the refrigerator and the parts bag behind the grille. Remove the four brackets (two on each side) that attach the shipping base to the refrigerator bottom. NOTE Do not remove tape and door bracing until the refrigerator is in its final location. 2. If necessary, reduce the tipping radius. See "Tipping Radius" for ceiling height requirements or "Reduce Tipping Radius" for step-by-step instructions. If you do not need to reduce the tipping radius, proceed to "Move the Refrigerator into House." Reduce Tipping Radius (If Required) Before bringing the refrigerator into the home, be sure there is adequate ceiling height to stand the refrigerator upright. See "Tipping Radius" in the "Installation Requirements" section for more information. If you do not have adequate ceiling height to stand the refrigerator upright, the tipping radius can be reduced by removing the top grille and side trims (see the following chart). Model 36 42 48 Reduced Tipping Radius 89" (225.9 cm) 901/2" (229.9 cm) 911/4" (231.8 cm) 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
17
Side Trim
Inset Installation Dimensions
1.
Measure the distance from point A (as shown) to the back
wall. Add 1/16" (1.6 mm) to this measurement to allow the
side panel to fit into the trim.
2.
If the panel is more than 11/32" (8.7 mm) thick, route the front
edge to allow the side panel to fit into the trim.
Recessed Inset Installation Dimensions
1.
Measure
the
distance
from
point
A
(as
shown)
to
back
wall.
2.
Route
the
front
edge
of
the
support
board
or
attach
a
3/8"
(9.5
mm)
board
to
hold
the
panel
in
the
cabinet
side
trim.
INSTALLATION INSTRUCTIONS
Unpack the Refrigerator
WARNING
Tip Over Hazard
Refrigerator is top heavy and tips easily when not
completely installed.
Keep doors taped closed until refrigerator is completely
installed.
Use two or more people to move and install refrigerator.
Failure to do so can result in death or serious injury.
IMPORTANT:
�
Do not remove the film covering until the refrigerator is in its
operating location.
�
All four leveling legs must contact the floor to support and
stabilize the full weight of the refrigerator.
�
Keep the cardboard shipping piece or plywood under the
refrigerator until it is installed in the operating location.
1.
Remove
and
save
the
literature
package
bag
taped
to
the
side
of
the
refrigerator
and
the
parts
bag
behind
the
grille.
Remove
the
four
brackets
(two
on
each
side)
that
attach
the
shipping
base
to
the
refrigerator
bottom.
NOTE
Do
not
remove
tape
and
door
bracing
until
the
refrigerator
is
in
its
final
location.
2.
If
necessary,
reduce
the
tipping
radius.
See
“
Tipping
Radius
”
for
ceiling
height
requirements
or
“
Reduce
Tipping
Radius
”
for
step-by-step
instructions.
If
you
do
not
need
to
reduce
the
tipping
radius,
proceed
to
“
Move
the
Refrigerator
into
House.
”
Reduce
Tipping
Radius
(If
Required)
Before
bringing
the
refrigerator
into
the
home,
be
sure
there
is
adequate
ceiling
height
to
stand
the
refrigerator
upright.
See
“
Tipping
Radius
”
in
the
“
Installation
Requirements
”
section
for
more
information.
If
you
do
not
have
adequate
ceiling
height
to
stand
the
refrigerator
upright,
the
tipping
radius
can
be
reduced
by
removing
the
top
grille
and
side
trims
(see
the
following
chart).
Model
Reduced Tipping Radius
36
89" (225.9 cm)
42
90
1
/
2
" (229.9 cm)
48
91
1
/
4
" (231.8 cm)
(18.0 mm)
11/16
"
(12.2 mm)
1/2
"
(13.9 mm)
9/16
"
(15.7 mm)
5/8
"
A
A