KitchenAid KBSN702MPA Owners Manual - Page 32
erature, Water Pressure, Water Temperature, Service Flow Rate, psi - 120 psi 207 kPa - 827 kPa
View all KitchenAid KBSN702MPA manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 32 highlights
Nonylphenol Meprobamate Carbamazepine DEET Metolachlor TCEP TCPP Phenytoin Ibuprofen Naproxen Bisphenol A 1400 ng/L ± 20% 400 ng/L ± 20% 1400 ng/L ± 20% 1400 ng/L ± 20% 1400 ng/L ± 20% 5000 ng/L ± 20% 5000 ng/L ± 20% 200 ng/L ± 20% 400 ng/L ± 20% 140 ng/L ± 20% 2000 ng/L ± 20% 200 ng/L 60 ng/L 200 ng/L 200 ng/L 200 ng/L 700 ng/L 700 ng/L 30 ng/L 60 ng/L 20 ng/L 300 ng/L 93.7% 94.9% 98.6% 98.6% 98.6% 98.1% 98.2% 94.5% 95.6% 96.9% 99.1% Test Parameters: pH = 7.5 ± 0.5 unless otherwise noted. Flow = 0.5 gpm (1.89 Lpm). Pressure = 60 psig (413.7 kPa). Temperature = 68°F to 71.6°F (20°C to 22°C). Rated service capacity = 200 gallons (757 liters). The compounds certified under NSF 401 have been deemed as "emerging compounds/incidental contaminants." Emerging compounds/ incidental contaminants are those compounds that have been detected in drinking water supplies at trace levels. While occurring at only trace levels, these compounds can affect the public acceptance/perception of drinking water quality. � For installation, operation, and maintenance instructions please � The product is for cold water use only. refer to the Owner's Manual. � The water system must be installed in compliance with state � It is important that operational, maintenance, and filter and local laws and regulations. replacement requirements be carried out for the product to perform as advertised. Property damage can occur if all instructions are not followed. � Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on � The disposable cartridge must be changed at least every 6 disinfected waters that may contain filterable cysts. EPA Est. months. No. 082047-TWN-001. � Use replacement filter part #EDR3RXD1/EDR3RXD1B. � Refer to the "Warranty" section (in the User Instructions or User � The filter monitor system measures the amount of water that Guide) for the Manufacturer's limited warranty, name and passes through the filter and alerts you when it is time to replace telephone number. the filter. To learn how to check the water filter status, see "Using the Controls" or "Water Filtration System" in the User Instructions Application Guidelines/Water Supply Parameters or User Guide. � After changing the water filter, flush the water system. See Water Supply Potable City or Well "Water and Ice Dispensers" or "Water Dispenser" in the User Water Pressure 30 psi - 120 psi (207 kPa - 827 kPa) Instructions or User Guide. � These contaminants are not necessarily in your water supply. Water Temperature 33°F - 100°F (0.6°C - 37.8° C) While testing was performed under standard laboratory conditions, actual performance may vary. Service Flow Rate 0.5 GPM (1.89 L/min.) @ 60 psi. � For installation, operation and maintenance instructions please refer Owner's Manual. Consumer Support 1.800.442.9991 By Whirlpool Corporation 2000 North M63 Benton Harbor, MI 49022 Made in Taiwan. � Your water filtration system will withstand up to 120 pounds per square inch (psi) water pressure. If your water supply is higher than 80 psi, install a pressure reducing valve before installing the water filtration system. *Class I particle size: >0.5 to 1 um †Based on the use of Cryptosporidium parvum oocysts ††Fibers greater than 10 um in length ®NSF is a registered trademark of NSF International. 32