KitchenAid KBSN708MPA Owners Manual - Page 24

Complete Installation, Water System Preparation, Installing the Odor Absorber on some models

Get KitchenAid KBSN708MPA PDF manuals and user guides View all KitchenAid KBSN708MPA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

Installing the Odor Absorber (on some models) The absorber should be installed behind the vented door, which is located (depending on your model) along either the rear or left interior wall near the top of the refrigerator compartment. 1. Remove the odor absorber from its packaging. 2. Snap the absorber in to place. 3. Pinch the tabs on the odor absorber to remove the absorber. Replacing the Odor Absorber The disposable odor absorber should be replaced every 6 months, when the status indicator has completely changed from white to red. To order a replacement odor absorber, see "Accessories" in the User Instructions or User Guide. � Remove the old odor absorber by squeezing in on the side tabs. � Remove the old status indicator. � Install the new odor absorber and status indicator using the instructions in the previous sections. Complete Installation 1. Turn the water supply line valve to the "Open" position. 2. Turn the refrigerator switch to the ON position. See "Power On/Off Switch" in the Use & Care Guide for instructions. Wait a few minutes. Check the water line connections for leaks. 3. Remove all boxes, parts packages and packing materials from the interior of the refrigerator. See the "Cleaning" section in the Use & Care Guide for instructions. Remove the film and cardboard from the grille and doors or door frame, depending on your model. 4. Install the shelves and bins in the refrigerator and freezer compartments. 5. The controls are preset at the factory to the midpoint setting. Make sure the compressor is operating properly and that all the lights are working. 6. Flush the water system before use. See "Water System Preparation." To get the most efficient use from your new built-in refrigerator, read the Use & Care Guide. Keep Installation Instructions and Use & Care Guide near the built-in refrigerator for easy reference. Water System Preparation Please read before using the water system. Follow the directions specific to your model. Style 1 (Dispenser Models) IMPORTANT: After connecting the refrigerator to a water source or replacing the water filter, follow the steps below to make sure that the water system is properly cleaned. This will flush air from the filter and water dispensing system, and prepare the water filter for use. Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts. NOTE: If your model has a base grille filter system, make sure the base grille filter is properly installed and the cap is in the horizontal position. 1. Open the freezer door and turn off the ice maker. The On/Off switch is located on the top right side of the freezer compartment. Move the switch to the OFF (right) setting as shown. 2. Use a sturdy container to depress and hold the water dispenser lever for 5 seconds, then release it for 5 seconds. Repeat until water begins to flow. Once water begins to flow, continue depressing and releasing the dispenser lever (5 seconds on, 5 seconds off) until a total of 3 gallons (12 L) has been dispensed. This will flush air from the filter and water dispensing system, and prepare the water filter for use. Additional flushing may be required in some households. NOTE: As air is cleared from the system, water may spurt out of the dispenser. 3. Open the freezer door and turn on the ice maker. Move the switch to the ON (left) position. NOTE: � Allow 24 hours to produce the first batch of ice. � Discard the first three batches of ice produced. � Allow 3 days to completely fill ice container. � Depending on your model, you may want to select the maximum ice feature to increase the production of ice. Style 2 (Non-Dispenser Models) IMPORTANT: After connecting the refrigerator to a water source or replacing the water filter, fill and discard two full containers of ice to prepare the water filter for use, before using the ice. Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts. NOTE: If your model has a base grille filter system, make sure the base grille filter is properly installed and the cap is in the horizontal position. 24

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
24
Installing the Odor Absorber (on some models)
The absorber should be installed behind the vented door, which is
located (depending on your model) along either the rear or left
interior wall near the top of the refrigerator compartment.
1.
Remove the odor absorber from its packaging.
2.
Snap the absorber in to place.
3.
Pinch the tabs on the odor absorber to remove the absorber.
Replacing
the
Odor
Absorber
The
disposable
odor
absorber
should
be
replaced
every
6
months,
when
the
status
indicator
has
completely
changed
from
white
to
red.
To
order
a
replacement
odor
absorber,
see
“Accessories”
in
the
User
Instructions
or
User
Guide.
�
Remove the old odor absorber by squeezing in on the side
tabs.
�
Remove the old status indicator.
�
Install the new odor absorber and status indicator using the
instructions in the previous sections.
Complete Installation
1.
Turn
the
water
supply
line
valve
to
the
“
Open
”
position.
2.
Turn
the
refrigerator
switch
to
the
ON
position.
See
“
Power
On/Off
Switch
”
in
the
Use
&
Care
Guide
for
instructions.
Wait
a
few
minutes.
Check
the
water
line
connections
for
leaks.
3.
Remove
all
boxes,
parts
packages
and
packing
materials
from
the
interior
of
the
refrigerator.
See
the
“
Cleaning
”
section
in
the
Use
&
Care
Guide
for
instructions.
Remove
the
film
and
cardboard
from
the
grille
and
doors
or
door
frame,
depending
on
your
model.
4.
Install
the
shelves
and
bins
in
the
refrigerator
and
freezer
compartments.
5.
The
controls
are
preset
at
the
factory
to
the
midpoint
setting.
Make
sure
the
compressor
is
operating
properly
and
that
all
the
lights
are
working.
6.
Flush
the
water
system
before
use.
See
“
Water
System
Preparation.
”
To get the most efficient use from your new built-in refrigerator,
read the Use & Care Guide. Keep Installation Instructions and
Use & Care Guide near the built-in refrigerator for easy reference.
Water System Preparation
Please read before using the water system. Follow the directions
specific to your model.
Style 1 (Dispenser Models)
IMPORTANT:
After connecting the refrigerator to a water source
or replacing the water filter, follow the steps below to make sure
that the water system is properly cleaned. This will flush air from
the filter and water dispensing system, and prepare the water filter
for use.
Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after
the system. Systems certified for cyst reduction may be used
on disinfected waters that may contain filterable cysts.
NOTE:
If your model has a base grille filter system, make sure the
base grille filter is properly installed and the cap is in the horizontal
position.
1.
Open the freezer door and turn off the ice maker. The On/Off
switch is located on the top right side of the freezer
compartment. Move the switch to the OFF (right) setting as
shown.
2.
Use
a
sturdy
container
to
depress
and
hold
the
water
dispenser
lever
for
5
seconds,
then
release
it
for
5
seconds.
Repeat
until
water
begins
to
flow.
Once
water
begins
to
flow,
continue
depressing
and
releasing
the
dispenser
lever
(5
seconds
on,
5
seconds
off)
until
a
total
of
3
gal
lons
(12
L)
has
been
dispensed.
This
will
flush
air
from
the
filter
and
water
dispensing
system,
and
prepare
the
water
filter
for
use.
Additional
flushing
may
be
required
in
some
households.
NOTE:
As
air
is
cleared
from
the
system,
water
may
spurt
out
of
the
dispenser.
3.
Open
the
freezer
door
and
turn
on
the
ice
maker.
Move
the
switch
to
the
ON
(left)
position.
NOTE:
�
Allow
24
hours
to
produce
the
first
batch
of
ice.
�
Discard
the
first
three
batches
of
ice
produced.
�
Allow
3
days
to
completely
fill
ice
container.
�
Depending
on
your
model,
you
may
want
to
select
the
maximum
ice
feature
to
increase
the
production
of
ice.
Style 2 (Non-Dispenser Models)
IMPORTANT:
After connecting the refrigerator to a water source
or replacing the water filter, fill and discard two full containers of
ice to prepare the water filter for use, before using the ice.
Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after
the system. Systems certified for cyst reduction may be used
on disinfected waters that may contain filterable cysts.
NOTE
:
If
your
model
has
a
base
grille
filter
system,
make
sure
the
base
grille
filter
is
properly
installed
and
the
cap
is
in
the
horizontal
position.