KitchenAid KCGC558JSS Installation Instructions - Page 18

Replace the burner grates.

Get KitchenAid KCGC558JSS PDF manuals and user guides View all KitchenAid KCGC558JSS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

6. With the burner ON (the burner will have to be lit manually with a lighter), and set to simmer LOW, adjust the simmer flame down to the proper BTU level. Using a 1/8" x 4¼" (3.2 mm x 10.8 cm) flat blade screwdriver, turn the simmer low-turndown adjustment screw clockwise until the flame height is at, or below, the bottom of the cap. If the flame becomes unstable and flickers or appears to race around the burner, the adjustment is too low and the screw should be adjusted counterclockwise until the flame is stable. Repeat this step for all surface burners. NOTE: Use a knob to adjust the burner valve. NOTE: Adjust each burner individually. 7. After adjustments are completed, replace the ignition switches onto the valves. 8. Lift up on the control console and set it back into place. For a proper fit, the flange of the control console must hook over the lip on the front of the cooktop. NOTE: It may be necessary to lift valve stems to align with console holes. Complete Installation 1. Refer to the "Make Gas Connection" section for properly connecting the cooktop to the gas supply. 2. Refer to the "Electronic Ignition System" section for proper burner ignition, operation, and burner flame adjustments. IMPORTANT: You may have to adjust the "LO" setting for each cooktop burner. Checking for proper cooktop burner flame is very important. The small inner cone should have a very distinct blue flame 1/4" (6.4 mm) to 1/2" (1.3 cm) long. The outer cone is not as distinct as the inner cone. Propane gas flames have a slightly yellow tip. 3. Refer to "Complete Installation" in the "Installation Instructions" section of this manual to complete this procedure. A B A. Control console flange B. Front lip of cooktop 9. Check that the control console is flush with the top edge of the cooktop. A A. Flush with cooktop 10. Replace the screws on each side of the control console. 11. Replace the bezels using the 2 screws which attach to the valve brackets, making note that there are front and rear bezels and will only attach properly in the correct location on the console. 12. Push the Surface Knobs onto the valve stems. 13. Replace the burner grates. 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
18
6.
With the burner ON (the burner will have to be lit manually
with a lighter), and set to simmer LOW, adjust the simmer
flame down to the proper BTU level. Using a 1/8" x 4¼"
(3.2 mm x 10.8 cm) flat blade screwdriver, turn the simmer
low‑turndown adjustment screw clockwise until the flame
height is at, or below, the bottom of the cap. If the flame
becomes unstable and flickers or appears to race around the
burner, the adjustment is too low and the screw should be
adjusted counterclockwise until the flame is stable. Repeat
this step for all surface burners.
NOTE:
Use a knob to adjust the burner valve.
NOTE:
Adjust each burner individually.
7.
After adjustments are completed, replace the ignition
switches onto the valves.
8.
Lift up on the control console and set it back into place. For
a proper fit, the flange of the control console must hook over
the lip on the front of the cooktop.
NOTE:
It may be necessary to lift valve stems to align with
console holes.
9.
Check that the control console is flush with the top edge of
the cooktop.
10.
Replace the screws on each side of the control console.
11.
Replace the bezels using the 2 screws which attach to the
valve brackets, making note that there are front and rear
bezels and will only attach properly in the correct location on
the console.
12.
Push the Surface Knobs onto the valve stems.
13.
Replace the burner grates.
Complete Installation
1.
Refer to the “Make Gas Connection” section for properly
connecting the cooktop to the gas supply.
2.
Refer to the “Electronic Ignition System” section for proper
burner ignition, operation, and burner flame adjustments.
IMPORTANT:
You may have to adjust the “LO” setting for
each cooktop burner.
Checking for proper cooktop burner flame is very important.
The small inner cone should have a very distinct blue flame
1/4" (6.4 mm) to 1/2" (1.3 cm) long. The outer cone is not as
distinct as the inner cone. Propane gas flames have a slightly
yellow tip.
3.
Refer to “Complete Installation” in the “Installation
Instructions” section of this manual to complete this
procedure.
A
B
A. Control console flange
B. Front lip of cooktop
A
A. Flush with cooktop