KitchenAid KGRS205TBT User Instructions - Page 5

Refrigerator Door and Drawer

Get KitchenAid KGRS205TBT - 30 Inch Gas Range PDF manuals and user guides View all KitchenAid KGRS205TBT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

Style 2 1. Create a service loop (minimum diameter of 2 ft [61 cm]) with the copper tubing. Avoid kinks when coiling the copper tubing. 2. Remove the plastic cap from water valve inlet port. Place a compression nut and sleeve on the copper tubing. 3. Insert the end of the copper tubing into the water valve inlet port. Shape tubing slightly so that the tubing feeds straight into the port to avoid kinks. 4. Slide the compression nut over the sleeve and screw into the water valve inlet port. A B C D A. Plastic water tubing C. Compression nut B. Sleeve D. Copper tubing 5. Using an adjustable wrench, hold the nut on the plastic water line to keep it from moving. Then, with a second wrench turn the compression nut on the copper tubing counterclockwise to completely tighten. Do not overtighten. A B C D A. "P" clamp B. Plastic water line C. Compression nut D. Copper tubing 6. Check connection by pulling on copper tubing. Attach the plastic water line to the refrigerator cabinet with a "P" clamp. 7. Turn on water supply to the refrigerator and check for leaks. Correct any leaks. Complete the Installation WARNING Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. 1. Plug into a grounded 3 prong outlet. NOTE: Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced. Allow 3 days to completely fill the ice storage bin. Refrigerator Door and Drawer Graphics are included later in this section. Remove and Replace Handles (Architect® Series) 1. Using a hex key, loosen the two setscrews located on the side of each handle. See Graphics 2 and 4. 2. Pull the handle straight out from the door. Make sure you keep the screws for reattaching handles. 3. To replace the handle, reverse the directions. Remove Handles (Panel Series) IMPORTANT: ■ Remove the door from refrigerator before removing handles. ■ You must remove the handles to remove the decorator panels or to reverse the door swing. 1. Using a Phillips screwdriver, remove the top door cap. See Graphic 3. 2. Tap the bottom edge of the refrigerator door handle upward with a rubber mallet. 3. Handle will slide up approximately ³⁄₄" (19.05 mm) and release from the door. 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
5
Style 2
1.
Create a service loop (minimum diameter of 2 ft [61 cm]) with
the copper tubing. Avoid kinks when coiling the copper
tubing.
2.
Remove the plastic cap from water valve inlet port. Place a
compression nut and sleeve on the copper tubing.
3.
Insert the end of the copper tubing into the water valve inlet
port. Shape tubing slightly so that the tubing feeds straight
into the port to avoid kinks.
4.
Slide the compression nut over the sleeve and screw into the
water valve inlet port.
5.
Using an adjustable wrench, hold the nut on the plastic water
line to keep it from moving. Then, with a second wrench turn
the compression nut on the copper tubing counterclockwise
to completely tighten. Do not overtighten.
6.
Check connection by pulling on copper tubing. Attach the
plastic water line to the refrigerator cabinet with a “P” clamp.
7.
Turn on water supply to the refrigerator and check for leaks.
Correct any leaks.
Complete the Installation
1.
Plug into a grounded 3 prong outlet.
NOTE:
Allow 24 hours to produce the first batch of ice. Discard
the first three batches of ice produced. Allow 3 days to completely
fill the ice storage bin.
Refrigerator Door and Drawer
Graphics are included later in this section.
Remove and Replace Handles (Architect
®
Series)
1.
Using a
³⁄₃₂
" hex key, loosen the two setscrews located on the
side of each handle. See Graphics 2 and 4.
2.
Pull the handle straight out from the door. Make sure you keep
the screws for reattaching handles.
3.
To replace the handle, reverse the directions.
Remove Handles (Panel Series)
IMPORTANT:
■
Remove the door from refrigerator before removing handles.
■
You must remove the handles to remove the decorator panels
or to reverse the door swing.
1.
Using a Phillips screwdriver, remove the top door cap. See
Graphic 3.
2.
Tap the bottom edge of the refrigerator door handle upward
with a rubber mallet.
3.
Handle will slide up approximately
³⁄₄
" (19.05 mm) and release
from the door.
A. Plastic water tubing
B. Sleeve
C. Compression nut
D. Copper tubing
A. “P” clamp
B. Plastic water line
C. Compression nut
D. Copper tubing
B
A
C
D
B
C
D
A
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING