KitchenAid KGRS205TWH Installation Instructions - Page 17

Natural Gas Orifice Spud Chart, IMPORTANT, Burner Rating, Color, Number

Get KitchenAid KGRS205TWH - 30inch Gas Range PDF manuals and user guides
UPC - 883049134512
View all KitchenAid KGRS205TWH manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

6. Position the broil burner against the roof of the oven cavity and attach with screw. AB C D A. Broil burner orifice hood B. Broil burner C. Broil burner locator pin D. Broil burner locator hole To Convert Surface Burners 1. If installed, remove the burner grates. 2. Remove the burner caps. 3. Using a Phillips screwdriver, remove the burner base. A C B D Use the following chart for correct Natural gas orifice spud for each burner. Refer to the rating plate on the lower right side of the front frame for proper sizing of Natural orifice spuds for each burner location. Natural Gas Orifice Spud Chart Burner Rating Color Number 5,000 BTU Clear 110N 9,200 BTU Clear 150N 12,000 BTU Clear 170N 16,000 BTU Clear 195N 5. Replace the LP gas orifice spud with correct Natural gas orifice spud. See the "Natural Gas Orifice Spud/Hood Chart." 6. Replace burner base and hand tighten the screws. 7. Replace burner cap. 8. Repeat steps 1 through 7 for the remaining burners. 9. Place LP gas orifice spuds in plastic parts bag for future use and keep with package containing literature. 10. Replace burner grates. 11. Reinstall storage drawer. See the "Replace Oven Racks and Storage Drawer" section for instructions. 12. Reinstall oven door. See the "Oven Door" section in the Use and Care Guide. 13. Complete installation. See "Make Gas Connection" and "Electronic Ignition System" sections. Checking for proper cooktop burner flame is very important. The small inner cone should have a very distinct blue flame ¼" to ½" long. The outer cone is not as distinct as the inner cone. Natural gas flames do not have yellow tips. IMPORTANT: You may have to adjust the "LO" setting for each cooktop burner. A. Burner cap C. Burner base screws B. Gas tube opening D. Burner base 4. Apply masking tape to the end of a 7.0 mm) nut driver to help hold the LP gas orifice spud in the nut driver while changing it. Press nut driver down onto the LP gas orifice spud and remove by turning it counterclockwise and lifting out. Set the LP gas orifice spud aside. A A. LP gas orifice spud 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
17
6.
Position the broil burner against the roof of the oven cavity
and attach with screw.
To Convert Surface Burners
1.
If installed, remove the burner grates.
2.
Remove the burner caps.
3.
Using a Phillips screwdriver, remove the burner base.
4.
Apply masking tape to the end of a
⁹⁄₃₂
" (7.0 mm) nut driver to
help hold the LP gas orifice spud in the nut driver while
changing it. Press nut driver down onto the LP gas orifice
spud and remove by turning it counterclockwise and lifting
out. Set the LP gas orifice spud aside.
Use the following chart for correct Natural gas orifice spud for
each burner. Refer to the rating plate on the lower right side of
the front frame for proper sizing of Natural orifice spuds for each
burner location.
Natural Gas Orifice Spud Chart
5.
Replace the LP gas orifice spud with correct Natural gas
orifice spud. See the “Natural Gas Orifice Spud/Hood Chart.”
6.
Replace burner base and hand tighten the screws.
7.
Replace burner cap.
8.
Repeat steps 1 through 7 for the remaining burners.
9.
Place LP gas orifice spuds in plastic parts bag for future use
and keep with package containing literature.
10.
Replace burner grates.
11.
Reinstall storage drawer. See the “Replace Oven Racks and
Storage Drawer” section for instructions.
12.
Reinstall oven door. See the “Oven Door” section in the Use
and Care Guide.
13.
Complete installation. See “Make Gas Connection” and
“Electronic Ignition System” sections.
Checking for proper cooktop burner flame is very important.
The small inner cone should have a very distinct blue flame
¼" to ½" long. The outer cone is not as distinct as the inner
cone. Natural gas flames do not have yellow tips.
IMPORTANT:
You may have to adjust the “LO” setting for
each cooktop burner.
A. Broil burner orifice hood
B. Broil burner
C. Broil burner locator pin
D. Broil burner locator hole
A. Burner cap
B. Gas tube opening
C. Burner base screws
D. Burner base
A. LP gas orifice spud
A
B
C
D
A
B
C
D
A
Burner Rating
Color
Number
5,000 BTU
Clear
110N
9,200 BTU
Clear
150N
12,000 BTU
Clear
170N
16,000 BTU
Clear
195N