KitchenAid KHWS02RWH Use and Care Guide - Page 4

Installation Requirements - pedestal

Page 4 highlights

INSTALLATION REQUIREMENTS Tools and Parts Assemble the necessary tools and supplies before beginning the washer installation. The parts supplied are in the washer drum. Tools needed for connecting the water inlet hoses s Pliers (that open to 1 39.5 mm]) s Flashlight (optional) Tools needed for installation s Open end wrench 17 mm and 13 mm s Level s Wood block s Ruler or measuring tape Parts supplied: Options Pedestal Are you placing the washer on a pedestal? You may purchase a pedestal separately for this washer. This pedestal will add about 13" (33 cm) to the height of your unit for a total height of approximately 51" (130 cm). Beaded strap Transport bolt hole plug (4) Alternate Parts Your installation may require additional parts. If you are interested in purchasing one of the items listed here, call the toll-free number on the cover or in the "Assistance or Service" section. If You Have You Will Need to Buy Laundry tub or standpipe taller than 96" (2.4 m) Sump pump system (if not already available) Overhead sewer Standard 20 gal. (76 L), 30" (76.2 cm) tall drain tub or utility sink and sump pump (available from local plumbing suppliers) Floor drain Siphon break, Part Number 285834; additional drain hose Part Number 8318155; and connector kit, Part Number 285835 Drain hose too short 4 ft (1.2 m) drain hose extension kit, Part Number 285863 Water faucets beyond reach of fill hoses 2 longer water fill hoses: 6 ft (1.8 m) Part Number 76314, 10 ft (3.0 m) Part Number 350008 Optional pedestal To order, call the dealer from whom you purchased your washer or refer to the "Assistance or Service" section of this manual. Ask for Part Number LAB2700PO (Meteorite). Stack Kit Are you planning to stack your KitchenAid washer and dryer? To do so you will need to purchase a Stack Kit. To order, call the dealer from whom you purchased your dryer or refer to the "Assistance or Service" section of this manual. Ask for Part Number 8541503. Location Requirements Selecting the proper location for your washer improves performance and minimizes noise and possible washer "walk." Your washer can be installed under a custom counter, or in a basement, laundry room, closet, or recessed area. See "Drain System." Companion appliance location requirements should also be considered. Proper installation is your responsibility. You will need s A water heater set to deliver 120°F (49°C) water to the washer. s A grounded electrical outlet located within 6 ft (1.8 m) of where the power cord is attached to the back of the washer. See "Electrical Requirements." s Hot and cold water faucets located within 4 ft (1.2 m) of the hot and cold water fill valves, and water pressure of 20-100 psi (137.9-689.6 kPa). s A level floor with a maximum slope of 1" (2.5 cm) under entire washer. Installing the washer on carpeting is not recommended. s A sturdy and solid floor to support the washer with a total weight (water and load) of 400 lbs (180 kg). Do not operate your washer in temperatures below 32°F (0°C). Some water can remain in the washer and can cause damage in low temperatures. 4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64

4
INSTALLATION REQUIREMENTS
Tools and Parts
Assemble the necessary tools and supplies before beginning the
washer installation. The parts supplied are in the washer drum.
Tools needed for connecting the water inlet hoses
Pliers (that open to 1
⁹⁄₁₆
" [39.5 mm])
Flashlight (optional)
Tools needed for installation
Open end wrench 17 mm and 13 mm
Level
Wood block
Ruler or measuring tape
Parts supplied:
Alternate Parts
Your installation may require additional parts. If you are interested
in purchasing one of the items listed here, call the toll-free
number on the cover or in the
Assistance or Service
section.
Options
Pedestal
Are you placing the washer on a pedestal? You may purchase a
pedestal separately for this washer. This pedestal will add about
13" (33 cm) to the height of your unit for a total height of
approximately 51" (130 cm).
Optional pedestal
To order, call the dealer from whom you purchased your washer
or refer to the
Assistance or Service
section of this manual. Ask
for Part Number LAB2700PO (Meteorite).
Stack Kit
Are you planning to stack your KitchenAid washer and dryer? To
do so you will need to purchase a Stack Kit.
To order, call the dealer from whom you purchased your dryer or
refer to the
Assistance or Service
section of this manual. Ask
for Part Number 8541503.
Location Requirements
Selecting the proper location for your washer improves
performance and minimizes noise and possible washer
walk.
Your washer can be installed under a custom counter, or in a
basement, laundry room, closet, or recessed area. See
Drain
System.
Companion appliance location requirements should also be
considered. Proper installation is your responsibility.
You will need
A water heater set to deliver 120
°
F (49
°
C) water to the
washer.
A grounded electrical outlet located within 6 ft (1.8 m) of
where the power cord is attached to the back of the washer.
See
Electrical Requirements.
Hot and cold water faucets located within 4 ft (1.2 m) of the
hot and cold water fill valves, and water pressure of
20-100 psi (137.9-689.6 kPa).
A level floor with a maximum slope of 1" (2.5 cm) under
entire washer. Installing the washer on carpeting is not
recommended.
A sturdy and solid floor to support the washer with a total
weight (water and load) of 400 lbs (180 kg).
Do not operate your washer in temperatures below 32
°
F (0
°
C).
Some water can remain in the washer and can cause damage in
low temperatures.
Beaded strap
Transport bolt hole plug (4)
If You Have
You Will Need to Buy
Laundry tub or
standpipe taller
than 96" (2.4 m)
Sump pump system (if not already
available)
Overhead sewer
Standard 20 gal. (76 L), 30" (76.2 cm)
tall drain tub or utility sink and sump
pump (available from local plumbing
suppliers)
Floor drain
Siphon break, Part Number 285834;
additional drain hose Part
Number 8318155; and connector kit,
Part Number 285835
Drain hose too
short
4 ft (1.2 m) drain hose extension kit, Part
Number 285863
Water faucets
beyond reach of
fill hoses
2 longer water fill hoses:
6 ft (1.8 m) Part Number 76314,
10 ft (3.0 m) Part Number 350008