KitchenAid KP26M1XDP Use & Care Guide - Page 10

Using the Pouring Shield - problems

Get KitchenAid KP26M1XDP - Professional 600 Series Stand Mixer PDF manuals and user guides
UPC - 050946970219
View all KitchenAid KP26M1XDP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

Auto-Reset Motor Protection If the stand mixer does not restart, If the stand mixer stops due to overload, slide the speed control see the "Troubleshooting Problems" section. lever to OFF. After a few minutes, the stand mixer will automatically reset. Slide the Speed Control Lever to the desired speed and continue mixing. Using the Pouring Shield* Attaching the Pouring Shield* 1. Make sure the speed control lever is set to the OFF/0 position. 2. Unplug the stand mixer. 3. Attach desired accessory and raise the mixing bowl. 4. Slide pouring shield collar around beater shaft, centering collar over rim of bowl. Using the Pouring Shield Pour ingredients into the mixing bowl through the chute portion of shield. IMPORTANT: Make sure the guides on the bottom of the chute rest on the rim of the bowl to keep ingredients from falling outside the bowl as they are added. Pouring Chute Removing the Pouring Shield 1. Make sure the speed control lever is set to the OFF/0 position. 2. Unplug the stand mixer. 3. Remove pouring chute from collar. 4. Slide pouring shield collar off bowl. 5. Lower the bowl support by turning the bowl-lift lever clockwise. 6. Remove accessory and the mixing bowl. Cleaning the Pouring Shield Wash in warm sudsy water. If you wish, you may place on the top rack of your dishwasher. *If Pouring Shield is included. 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
10
Attaching the Pouring Shield*
1.
Make sure the speed control lever
is set to the OFF/0 position.
2.
Unplug the stand mixer.
3.
Attach desired accessory and raise
the mixing bowl.
4.
Slide pouring shield collar around
beater shaft, centering collar over
rim of bowl.
Using the Pouring Shield
Pour ingredients into the mixing
bowl through the chute portion of
shield.
IMPORTANT:
Make sure the guides
on the bottom of the chute rest on
the rim of the bowl to keep
ingredients from falling outside the
bowl as they are added.
Using the Pouring Shield*
Removing the Pouring Shield
1.
Make sure the speed control lever
is set to the OFF/0 position.
2.
Unplug the stand mixer.
3.
Remove pouring chute from collar.
4.
Slide pouring shield collar off
bowl.
5.
Lower the bowl support by
turning the bowl-lift lever
clockwise.
6.
Remove accessory and the mixing
bowl.
Cleaning the Pouring Shield
Wash in warm sudsy water. If you
wish, you may place on the top rack
of your dishwasher.
*If Pouring Shield is included.
Auto-Reset Motor Protection
If the stand mixer stops due to
overload, slide the speed control
lever to OFF. After a few minutes,
the stand mixer will automatically
reset. Slide the Speed Control Lever
to the desired speed and continue
mixing.
If the stand mixer does not restart,
see the “Troubleshooting Problems”
section.
Pouring
Chute