KitchenAid KUDE48FXSP Installation Guide - Page 15

Install Door Handle, on some models, Custom Panel Dimensions, Install Custom Panel

Get KitchenAid KUDE48FXSP PDF manuals and user guides View all KitchenAid KUDE48FXSP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

Install Door Handle (on some models) IMPORTANT: Do not scratch the front panel during this procedure. Remove the door handle and hardware bag containing the setscrews and hex key from the cardboard box. Setscrews are already installed in the handle. Place handle on mounting studs with the setscrews facing down. Push the door handle tightly against the door. Insert the short end of the hex key into the setscrews. Tighten the setscrews ¹⁄₄ turn past snug. Retain hex key with Installation Instructions. Custom Panel Dimensions Install Custom Panel Follow steps below: A customer supplied panel must weigh no more than 16 lbs (7.3 kg) and must be made to specific dimensions. It is recommended that a cabinetmaker cut the customer panel because of the precise dimensions needed. NOTES: ■ The handle for the custom panel is not included. ■ All mounting hardware supplied is for a ³⁄₄" (19.1 mm) thick wood panel. If a thinner wood panel or materials other than wood are used, it is the customer's responsibility to obtain the proper length screws and adjust the pilot holes accordingly. IMPORTANT: Use a moisture-resistant sealer on both sides and all edges of the panel to avoid damage from moisture. WARNING Excessive Weight Hazard Use two or more people to move and install dishwasher. Failure to do so can result in back or other injury. Using 2 or more people, stand the dishwasher up. NOTE: Do not install kick plate until instructed to do so. 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
15
Install Door Handle
(on some models)
IMPORTANT:
Do not scratch the front panel during this
procedure.
Remove the door handle and hardware bag containing the
setscrews and hex key from the cardboard box. Setscrews are
already installed in the handle. Place handle on mounting studs
with the setscrews facing down. Push the door handle tightly
against the door. Insert the short end of the hex key into the
setscrews. Tighten the setscrews
¹⁄₄
turn past snug.
Retain hex key with Installation Instructions.
Custom Panel Dimensions
Install Custom Panel
Follow steps below:
A customer supplied panel must weigh no more than 16 lbs
(7.3 kg) and must be made to specific dimensions. It is
recommended that a cabinetmaker cut the customer panel
because of the precise dimensions needed.
NOTES:
■
The handle for the custom panel is not included.
■
All mounting hardware supplied is for a
³⁄₄
" (19.1 mm) thick
wood panel. If a thinner wood panel or materials other than
wood are used, it is the customer’s responsibility to obtain the
proper length screws and adjust the pilot holes accordingly.
IMPORTANT:
Use a moisture-resistant sealer on both sides and
all edges of the panel to avoid damage from moisture.
Using 2 or more people, stand the dishwasher up.
NOTE:
Do not install kick plate until instructed to do so.
WARNING
Excessive Weight Hazard
Use two or more people to move and install
dishwasher.
Failure to do so can result in back or other injury.