KitchenAid KUDE48FXSP Installation Guide - Page 17

door using hole in liner as a guide.

Get KitchenAid KUDE48FXSP PDF manuals and user guides View all KitchenAid KUDE48FXSP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Check custom tape alignment with metal door slots; verify tape is right-side up, and that the tape does not overhang the metal door on the top, bottom or side interfaces. Remove the backing from the custom tape by pulling straight down on the liner. Align the custom tape to the keyhole slots on the metal door (see image) and apply. Repeat steps for one side and then the other. NOTE: The adhesive on the tape is aggressive, so proper alignment and attachment to the metal door needs to occur on the first try. Open the door and align top edges. Predrill 2 pilot holes using a drill bit. Use tape to mark the drill bit to gauge hole depth. Drill pilot holes approximately 1¹⁄₂" (3.8 cm) into the top corners of the door using hole in liner as a guide. Install 2 long screws supplied in top corners to secure custom wood panel in place. Align the studs on the custom wood panel to the keyhole slots on the door assembly. Ensure that all 4 plastic studs are engaged in the keyhole slots. Slide wood panel down until the top surface of the wooden panel is flush with the top of the door. Remove the short screws (3rd from top) on either side of the inner door panel. Predrill 2 pilot holes using a drill bit. Use tape to mark the drill bit to gauge the hole depth. Drill pilot holes approximately 1¹⁄₂" (3.8 cm) using the door liner hole as a guide into the panel. Install the 2 remaining long screws. 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
17
Check custom tape alignment with metal door slots; verify tape is
right-side up, and that the tape does not overhang the metal door
on the top, bottom or side interfaces. Remove the backing from
the custom tape by pulling straight down on the liner. Align the
custom tape to the keyhole slots on the metal door (see image)
and apply. Repeat steps for one side and then the other.
NOTE:
The adhesive on the tape is aggressive, so proper
alignment and attachment to the metal door needs to occur on
the first try.
Align the studs on the custom wood panel to the keyhole slots on
the door assembly. Ensure that all 4 plastic studs are engaged in
the keyhole slots. Slide wood panel down until the top surface of
the wooden panel is flush with the top of the door.
Open the door and align top edges. Predrill 2 pilot holes using a
³⁄₃₂
" drill bit. Use tape to mark the drill bit to gauge hole depth. Drill
pilot holes approximately 1
¹⁄₂
" (3.8 cm) into the top corners of the
door using hole in liner as a guide.
Install 2 long screws supplied in top corners to secure custom
wood panel in place.
Remove the short screws (3rd from top) on either side of the inner
door panel. Predrill 2 pilot holes using a
³⁄₃₂
" drill bit. Use tape to
mark the drill bit to gauge the hole depth. Drill pilot holes
approximately 1
¹⁄₂
" (3.8 cm) using the door liner hole as a guide
into the panel. Install the 2 remaining long screws.