Home » Konica Minolta Manuals » Printers » Konica Minolta Fiery proServer for KIP C7800 » Manual Viewer

Konica Minolta Fiery proServer for KIP C7800 User Manual - Page 49

Mis-feed Errors

View all Konica Minolta Fiery proServer for KIP C7800 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

3. 1 Mis-feed Error If a media mis-feed happens, the UI screen shows any of the following 4 figures that indicates where a mis-feed has been detected. The figure would indicate only a "primary" mis-feed location. For a mis-feed while processing multiple sheets, there would be another mis-feed location(s) than the UI indication. This section instructs you to check for a mis-fed media in the entire media path from the exit to the entrance regardless of the UI indication. NOTE (1) Follow the instruction on the next page, starting with "open the Rear Door." (2) While a mis-feed happens, avoid doing the followings. Doing so may damage the surface of the Drum. - Rewind a roll media before you open Rear Door - Open a Roll Deck before you open Rear Door To avoid these, as mentioned in the instruction on the next page, it is very important to open the Rear Door first when a mis-feed happens. 3-2 Chapter 3 Troubleshooting

Section	Page
KIP C7800 User Manual (A.1)	1
Safety Warning	3
WARNING	4
CAUTION	5
POWER CORD INSTRUCTION	6
Chapter 1 Before Use	9
1. 1 Installation Requirements	10
1. 2 Originals Prohibited from Duplication	11
1. 3 Features	12
1. 4 Specifications	13
1. 5 Appearance	15
1. 5. 1 Front view	15
1. 5. 2 Left side view	16
1. 5. 3 Rear view	17
1. 6 Specifications for the Printing Paper	19
1. 6. 1 Papers not available to use	19
1. 6. 2 Keeping the paper in the custody	20
1. 6. 3 Treatment against environmental condition	21
Chapter 2 Basic Operations	22
2. 1 Turning on the KIP C7800	23
2. 2 Turning off the KIP C7800	25
2. 3 Replacing the Roll Media	27
2. 4 Setting Cut Sheet Media to Bypass Feeder	32
2. 4. 1 Loading Small Size Sheet	33
2. 4. 2 Loading Large Size Sheet	35
2. 5 Replacing the Toner Cartridge	37
2. 6 Replacing the Waste Toner Box	41
2. 7 Initial Cut (Straighten the leading edge of roll media)	45
2. 8 Sleep Mode	47
Chapter 3 Troubleshooting	48
3. 1 Mis-feed Errors	49
3. 1. 1 How to Remove Mis-fed Media	50
3. 2 Open Errors	58
3. 2. 1 Roll Deck 1 Open	58
3. 2. 2 Roll Deck 2 Open	58
3. 2. 3 Roll Deck 3 Open	59
3. 2. 4 Roll Deck 1 - Cutter Cover Open	59
3. 2. 5 Roll Deck 2 - Cutter Cover Open	60
3. 2. 6 Roll Deck 3 - Cutter Cover Open	60
3. 2. 7 Sheet Bypass Open	61
3. 2. 8 Left Door Open	61
3. 2. 9 Rear Door Open	62
3. 2.10 Fuser Exit Door Open	62
3. 3 Other Operator Call Error	63
3. 3. 1 Printer out of paper	63
3. 3. 2 Printer out of toner	63
3. 3. 3 Printer waste toner bottle full	64
3. 3. 4 Web Cleaner Empty	65

Match case Limit results 1 per page

Chapter 3

Troubleshooting

3-2

3. 1

Mis-feed Error

If a media mis-feed happens, the UI screen shows any of the following 4 figures that indicates

where a mis-feed has been detected.

The figure would indicate only a “primary” mis-feed location. For a mis-feed while processing

multiple sheets, there would be another mis-feed location(s) than the UI indication.

This section instructs you to check for a mis-fed media in the entire media path from the exit to the

entrance regardless of the UI indication.

NOTE

(1) Follow the instruction on the next page, starting with “open the Rear Door.”

(2) While a mis-feed happens,

avoid

doing the followings.

Doing so may damage the surface of the Drum.

- Rewind a roll media before you open Rear Door

- Open a Roll Deck before you open Rear Door

To avoid these, as mentioned in the instruction on the next page, it is very important to

open the Rear Door first when a mis-feed happens.