Kyocera KM-1810 Print System M Installation Handbook (Setup) - Page 13

Error Indications in this printer, Error code, Procedure - copier error codes

Get Kyocera KM-1810 PDF manuals and user guides View all Kyocera KM-1810 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

3. Troubleshooting 3-2 When an error code or error messages appears... If an error code appear on the operation panel, first check the following tables for cause of the trouble and then perform the corresponding procedure. For more detailed information, refer to the Instruction Handbook for your copier as well as the Instruction Handbook for any optional equipment that is installed in your machine. Error Indications in this printer If "Prt" is displayed and the Memory Overflow/Data Error indicator flashes while the machine is in the copier mode, an error has occurred with the printer functions of this machine. Press the Printer key and check the cause of the error. Refer to the following tables for the corresponding error code and appropriate correction procedure. Error code E01 E02 E03 E04 E05 E06 E07 E25 E30 Procedure A paper jam has occurred. Remove the jammed paper. The drawer has run out of paper or a paper jam has occurred. Add paper or remove the jammed paper, as appropriate. One or both drawers are not set properly in the printer. Insert both drawers securely. The size of paper selected for printing does not match the size of paper in the drawer. Replace the paper in the drawer with that of the correct size. * If you want to force-print onto the current size of paper, press the Start [GO] key. If you want to switch to and print from a different drawer, press the Paper Select key until the desired drawer is selected. If you want to cancel the printing operation completely, press the Stop/Reset key. The drawer has run out of paper. Add paper. One of the covers is open. Close the covers securely. Differ from actual size. Check drawer sizesetting. The amount of paper stacked in the Inner tray has exceeded the acceptable capacity. Remove all paper from the Inner tray and then press the Start [GO] key to continue printing. * If you want to cancel the printing operation completely, press the Stop/Reset key. Trouble has occurred within the printer. Contact your service representative or an authorized service center. 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
6
3. Troubleshooting
3-2
When an error code or error messages appears…
If an error code appear on the operation panel, first check the following tables for cause of the trouble and then perform the corresponding
procedure. For more detailed information, refer to the Instruction Handbook for your copier as well as the Instruction Handbook for any optional
equipment that is installed in your machine.
Error Indications in this printer
If
“
Prt
”
is displayed and the Memory Overflow/Data Error indicator flashes while the machine is in the copier mode,
an error has occurred with the printer functions of this machine. Press the Printer key and check the cause of the
error. Refer to the following tables for the corresponding error code and appropriate correction procedure.
Error code
E01
E02
E03
E04
E05
E06
E07
E25
E30
Procedure
A paper jam has occurred. Remove the jammed paper.
The drawer has run out of paper or a paper jam has occurred. Add paper or remove the jammed paper, as appropriate.
One or both drawers are not set properly in the printer. Insert both drawers securely.
The size of paper selected for printing does not match the size of paper in the drawer. Replace the paper in the drawer with
that of the correct size.
*If you want to force-print onto the current size of paper, press the Start [GO] key. If you want to switch to and print from a
different drawer, press the Paper Select key until the desired drawer is selected. If you want to cancel the printing operation
completely, press the Stop/Reset key.
The drawer has run out of paper. Add paper.
One of the covers is open. Close the covers securely.
Differ from actual size. Check drawer sizesetting.
The amount of paper stacked in the Inner tray has exceeded the acceptable capacity. Remove all paper from the Inner tray
and then press the Start [GO] key to continue printing.
*If you want to cancel the printing operation completely, press the Stop/Reset key.
Trouble has occurred within the printer. Contact your service representative or an authorized service center.