LG 32LH1DC1 Operation Guide - Page 22

PILLOW SPEAKER SETUP, How to connect

Get LG 32LH1DC1 - LG - 32inch LCD TV PDF manuals and user guides
UPC - 719192172524
View all LG 32LH1DC1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

EXTERNAL EQUIPMENT SETUP EXTERNAL EQUIPMENT SETUP PILLOW SPEAKER SETUP ■ Here shown may be somewhat different from your TV. 1. How to connect Connect the PILLOW JACK IN the Pillow Speaker output 1 jack on the back of the TV. Connect an accessory pillow speaker or wired remote 2 control unit to this 6-pin jack. 3 Select PILLOW SPEAKER on the rear panel of the TV. *Note: If the pillow Speaker switch is set to Pillow Speaker, no sound will be heard from the TV speakers. If pillow speaker switch is set to the Pillow Speaker position, Auto Volume will be grayed out and not accessible on the Sound menu. Use a pillow speaker by Curbell, Model A-16455-02 or other UL recognized pendant control bearing the warning: "Risk of fire if used in oxygen enriched atmosphere. Keep pendant control away from oxygen equipment." Controlling the TV with Serial Data The TV is capable of being controlled by a single-wire, serial data signal. This is a LG patented technology and is being implemented by certain brands of "smart" pillow speakers, such as Curbell's "GEN-II" models. Pillow speaker not included with TV. Pillow Speaker Interface This connector furnishes three control lines and an audio output. A patient-pendant remote control, or entertainment audio and nurse call system may be connected here. All lines are isolated from the AC power line and earth ground. (Optoisolators isolate the control lines, and a transformer isolates the audio. There are no relays or inductive components in the control lines.) Pin No. 1 2 3 4 5 Purpose External TV On/Off switch. (Not used.) External Channel Up switch or Data in. Common connection for control, data, and audio output. Impedance to earth ground is a 10-meg resistor in parallel with a 1100 pf capacitor. Isolated audio output. Nominal 14-ohm source impedance with short circuit protection. Intended for a pillow speaker with a low-impedance pad-type volume control. 6 External Channel Down switch. Controlling the TV with Mechanical Switches Pin 4 (common) is momentarily connected to pin 1, 3, or 6 via push-action switches to control On/Off and Channel Up/Down. These pins are at +13 volts DC (when measured from pin 4) with the switches open. Current draw is 8 mA when a switch is closed. (This operation is identical to previous LG models using the 5-Wire Interface except that only +7 volts DC was supplied and current draw was only 2.5 mA.) 22

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
EXTERNAL EQUIPMENT SETUP
22
EXTERNAL EQUIPMENT SETUP
PILLOW SPEAKER SETUP
■
Here shown may be somewhat different from your TV.
Connect the PILLOW JACK IN the Pillow Speaker output
jack on the back of the TV.
1. How to connect
1
Connect an accessory pillow speaker or wired remote
control unit to this 6-pin jack.
2
Select PILLOW SPEAKER on the rear panel of the TV.
3
*Note: If the pillow Speaker switch is set to Pillow Speaker, no sound will
be heard from the TV speakers. If pillow speaker switch is set to the
Pillow Speaker position, Auto Volume will be grayed out and not
accessible on the Sound menu.
Use a pillow speaker by Curbell, Model A-16455-02 or
other UL recognized pendant control bearing the warning:
“Risk of fire if used in oxygen enriched atmosphere.
Keep pendant control away from oxygen equipment.”
The TV is capable of being controlled by a single-wire,
serial data signal. This is a LG patented technology and is
being implemented by certain brands of “smart” pillow
speakers, such as Curbell’s “GEN-II” models.
Controlling the TV with Serial Data
This connector furnishes three control lines and an audio
output. A patient-pendant remote control, or entertainment
audio and nurse call system may be connected here. All
lines are isolated from the AC power line and earth ground.
(Optoisolators isolate the control lines, and a transformer
isolates the audio. There are no relays or inductive
components in the control lines.)
Pillow Speaker Interface
Pin 4 (common) is momentarily connected to pin 1,
3, or 6 via push-action switches to control On/Off
and Channel Up/Down. These pins are at +13 volts
DC (when measured from pin 4) with the switches
open. Current draw is 8 mA when a switch is
closed. (This operation is identical to previous LG
models using the 5-Wire Interface except that only
+7 volts DC was supplied and current draw was
only 2.5 mA.)
Controlling the TV with Mechanical Switches
Pillow speaker not included with TV.
Pin No.
Purpose
1
External TV On/Off switch.
2
(Not used.)
3
External Channel Up switch or Data in.
6
External Channel Down switch.
4
Common connection for control, data, and audio output.
Impedance to earth ground is a 10-meg resistor in parallel
with a 1100 pf capacitor.
5
Isolated audio output. Nominal 14-ohm source impedance
with short circuit protection. Intended for a pillow speaker
with a low-impedance pad-type volume control.