LG 32LH1DC1 Operation Guide - Page 57

Cloning Connections/learning Setup

Get LG 32LH1DC1 - LG - 32inch LCD TV PDF manuals and user guides
UPC - 719192172524
View all LG 32LH1DC1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

CLONING CONNECTIONS/LEARNING SETUP - Connections for the LT2002 Clone Programmer to Learn the 32LH1DC1 Master TV Setup Antenna or CATV Ferrite Core (TDK, ZCAT 2035-0930) COMMERCIAL MODE Warning: Do not use LT2002 if a Lodge Net PPV card is installed in TV or clone programmer device will be damaged. Master 32LH1DC1 Clone Programmer *Note1: It is assumed that the 32LH1DC1 is connected to a signal source, the source selected is Antenna (RF) In, the signal is from an Analog channel, not a digital channel, all equipment is connected to power and turned on and the LT2002 Clone Programmer main menu (THE CLONE HAS CONTROL OF THE TV) menu is displayed on the TV screen, the clone programmer LED is blinking the required heart beat pattern, see above and next page. *Note2: Once the clone is connected, do not touch the unit or otherwise disturb it or the MPI connections. Any disturbance while the clone is operating may disrupt the master setup transfer or copying etc. Before you begin cloning... • The Master 32LH1DC1 should be connected to a good, stable signal from an over-the-air antenna or cable service Analog channel and connected to power. (See above.) • Teaching and Learning is only possible between identical model devices. (However, the LT2002 Clone programmer can store up to 3 different 'master' setups.) WARNING: Copying a blank or incorrect memory into a TV, STB or other device will cause the TV, STB or other device to operate erratically or become inoperable. • Use an Installer's remote to operate Learning and Teaching menus. • Make sure that the batteries in the Clone programmer are fresh. • If batteries are removed, the Clone Clock time will be lost. • Decide if you want to set the time from the Clone programmer or copy the time to the Clone programmer; from a compatible TV which has the clock set to the current time. • Setting the time and transferring it to the Clone or other device is a separate procedure. • Follow the connection diagram above to connect the Clone to a Master 32LH1DC1 TV display panel. After learning is complete, to another identical 32LH1DC1 TV display panel to "teach" it the master setup. • After the 32LH1DC1s setup has been copied to another identical 32LH1DC1, that identical unit with the copied setup, needs to be disconnected from power for about 15 seconds to activate the newly-copied setup. • See the Clone Troubleshooting section to resolve problems. Turn to the next page to continue Cloning Setup. 57

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
COMMERCIAL MODE
57
CLONING CONNECTIONS/LEARNING SETUP
*Note1: It is assumed that the 32LH1DC1 is connected to a signal source, the source selected is Antenna (RF) In, the signal is from an
Analog channel, not a digital channel, all equipment is connected to power and turned on and the LT2002 Clone Programmer main menu
(THE CLONE HAS CONTROL OF THE TV) menu is displayed on the TV screen, the clone programmer LED is blinking the required heart
beat pattern, see above and next page.
*Note2: Once the clone is connected, do not touch the unit or otherwise disturb it or the MPI connections. Any disturbance while the clone is
operating may disrupt the master setup transfer or copying etc.
-
Connections for the LT2002 Clone Programmer to Learn the 32LH1DC1 Master TV Setup
Clone Programmer
Master 32LH1DC1
Ferrite Core
(TDK, ZCAT
2035-0930)
Antenna
or CATV
Warning: Do not use LT2002
if a Lodge Net PPV card is
installed in TV or clone
programmer device will be
damaged.
Before you begin cloning...
• The Master 32LH1DC1 should be connected to a
good, stable signal from an over-the-air antenna or
cable service Analog channel and connected to power.
(See above.)
•
Teaching and Learning is only possible between
identical model devices. (However, the LT2002 Clone
programmer can store up to 3 different ‘master’
setups.)
WARNING: Copying a blank or incorrect memory into a
TV, STB or other device will cause the TV, STB or
other device to operate erratically or become
inoperable.
• Use an Installer’s remote to operate Learning and
Teaching menus.
• Make sure that the batteries in the Clone programmer
are fresh.
•
If batteries are removed, the Clone Clock time will be
lost.
• Decide if you want to set the time from the Clone
programmer or copy the time to the Clone
programmer; from a compatible TV which has the clock
set to the current time.
• Setting the time and transferring it to the Clone or
other device is a separate procedure.
• Follow the connection diagram above to connect the
Clone to a Master 32LH1DC1 TV display panel. After
learning is complete, to another identical 32LH1DC1
TV display panel to “teach” it the master setup.
• After the 32LH1DC1s setup has been copied to
another identical 32LH1DC1, that identical unit with
the copied setup, needs to be disconnected from
power for about 15 seconds to activate the
newly-copied setup.
•
See the Clone Troubleshooting section to resolve
problems.
Turn to the next page to continue Cloning Setup.