LG 32LH1DC1 Operation Guide - Page 63

COMMERCIAL MODE (Continued from previous page) The value range is 0 to 63, with 63 as the default, which gives the user the full range of volume control, if item 008 MIN VOLUME is also set at 0. Change values with Left/Right ADJ button. It may be best to set the same value on every 32LH1DC1. *Note: The maximum volume level cannot have a value setting lower than the MIN VOLUME level (described previously). 010 - MUTE DISABLE Enables or disables sound mute function. If set to 1, sound cannot be muted, mute is disabled. If set to 0, sound can be muted. 011 - KEY DEFEAT (Keyboard Defeat) If set to 1, key defeat prevents the end user from accessing the on-screen menus with the display front panel-MENU, SELECT, and Left / Right arrow keys and TV/AV do not function. If set to 0, those keys do function. *Note: The menus can always be accessed by pressing MENU on the remote. 012 - IR BANKS EN. (IR Banks Enable) For direct access to a particular Channel Bank. When enabled, installer can access a channel bank by inputting the IR code for the bank. 013 - SCAN MODE Allows variation in setting the On/Off with Channel UP/DOWN. You may opt for TV channels only; TV channels + Off/ON; TV channels + FM radio; TV channels + FM radio + Off/On with these set-tings for Scan Mode: SCAN MODE Characteristics 0 Channel up/down keys change channels only. 1 Channel down below the lowest channel (or channel up higher than the highest) and TV turns off. 014 - STRT CH IN SM (Start Channel in Scan Mode) When set to 1, installs TV On/Off event below the start channel at TV turn on. 015 - SLEEP TIMER If set to 1, the SLEEP TIMER feature may be used. If set to 0, the Sleep Timer is not available. 016 - EN TIMER (Enable On/Off Timers) If set to 1, Timer function is available to user. Set to 0 to disable On/Off Timer functions. (Clock must be set in order to use Timers.) 017 - ALARM Gives the installer the option of making the Alarm function available to the end user. If set to 1, Alarm function is available to end user. Set to 0 to disable the Alarm function. *Note: The maximum volume level cannot have a value setting lower than the MIN VOLUME level (described previously). Installer should leave item 20 FEATURE LEVEL set to 1 (default). 020 - FEATURE LEVEL Default set to ZEN 1 for LG IR remote control opera-tion. Set O, P LBL for LG Private Label IR remote con-trol operation. Warning: Do not set to "0" or remote will not control TV. 021 - V-CHIP (Parental Control) Set to 1 to activate V-Chip (Parental Control); have it available to end user to filter and control or otherwise restrict programming content that can appear. Set to 0 to turn V-Chip feature Off, not available to user; no programming restrictions can be set. 022 - MAX BLK HRS (Maximum Block Hours) Sets hours from 0 to 99 for the maximum V-Chip (Parental Control) block hours. Default setting is for 12 blocking hours. 023 - CAPTION LOCK Set to 1 to restore previous caption On/Off state after turn Off. If set to 0, captions are always Off at turn On. 025 - FUNCTION PRE. (Function Preview) Set to 0 to suppress CHANNEL PREVIEW from the FUNCTION menu with some Pay-Per-View systems. 027 - HOSPITAL MODE The default is 2 (which favors most hospitals). With this setting two things are affected: Channel Banks 1, 2, and 3 are accessible, while Bank 4 is inactive. 028 - CH. OVERIDE (Channel Override) If set to 1, the user can select channels with either Channel up/down or by direct keypad entry. If set to 0, only those channels that are entered for scanning can be selected. 029 - OLD OCV (On Command VideoTM) Set to 1 for operation with systems from On Command Corporation. (Continued on next page) 63