LG DLEX9500K Owners Manual - Page 17

Reversing the Door

Get LG DLEX9500K PDF manuals and user guides View all LG DLEX9500K manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

ENGLISH INSTALLATION 17 Reversing the Door wWarning THE DRYER DOOR IS VERY LARGE AND HEAVY. Two or more people are required when reversing the door. Failure to follow the warnings below can result in damage to the dryer, property damage or injury to persons. • To avoid damage to the dryer or the door, support the door with a stool or box that fits under the door, or have an assistant support the weight of the door. • Always reverse the door BEFORE stacking the dryer on top of the washer. • Avoid dropping the door to avoid damage to the door or the floor. Tools Needed: flat blade screwdriver, Phillips screwdriver Before Starting 1. Unplug the machine or turn off the power supply at the main circuit before reversing the door. Open the dryer door. Reversing the Door's Hinge and Strike 1. Remove the four screws on the right door frame (handle and strike), lift it off, and set the parts aside. (The two center strike screws are longer.) 2. Remove the four screws on the left door frame (hinge assembly). 3. Carefully lift out the hinge assembly, revealing the wire harness connector at the top of the hinge. Depress the center lock tab to disconnect the wire harness connector. 4. Rotate the hinge assembly 180 degrees and connect the wire harness to the connector in the bottom right side of the door. 5. Install the hinge assembly in the recess on the right side of the door, tucking the wire harness in the corner to make room. Insert and tighten the four screws. 6. Rotate the handle removed in step one 180 degrees and install it on the left side of the door using the two shorter screws. Use the longer screws to mount the door strike in the center. wWarning Be sure to support the weight of the door before removing the hinge screws. Removing the Door 1. While supporting the door, remove the four hinge screws. 2. Carefully pull the door away from the cabinet to reveal the wire harness behind the hinge at the top. Depress the side lock tab to disconnect the wire harness connector. The twist tie and cap should prevent the wire harness from pulling back into the cabinet. 3. Remove the door from the cabinet cover. Set the door face down on a protected work surface. Cap R Frame L Frame R

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
17
ENGLISH
Tools Needed:
flat blade screwdriver, Phillips screwdriver
Before Starting
1. Unplug the machine or turn off the power supply at
the main circuit before reversing the door. Open the
dryer door.
w
WARNING
Be sure to support the weight of the door before
removing the hinge screws.
Removing the Door
1. While supporting the door, remove the four hinge
screws.
2. Carefully pull the door away from the cabinet to reveal
the wire harness behind the hinge at the top. Depress
the side lock tab to disconnect the wire harness
connector. The twist tie and cap should prevent the
wire harness from pulling back into the cabinet.
3. Remove the door from the cabinet cover. Set the door
face down on a protected work surface.
Cap R
Reversing the Door’s Hinge and Strike
1. Remove the four screws on the right door frame
(handle and strike), lift it off, and set the parts aside.
(The two center strike screws are longer.)
2. Remove the four screws on the left door frame (hinge
assembly).
3. Carefully lift out the hinge assembly, revealing the
wire harness connector at the top of the hinge.
Depress the center lock tab to disconnect the wire
harness connector.
4. Rotate the hinge assembly 180 degrees and connect
the wire harness to the connector in the bottom right
side of the door.
5. Install the hinge assembly in the recess on the right
side of the door, tucking the wire harness in the corner
to make room. Insert and tighten the four screws.
6. Rotate the handle removed in step one 180 degrees
and install it on the left side of the door using the two
shorter screws. Use the longer screws to mount the
door strike in the center.
Reversing the Door
w
WARNING
THE DRYER DOOR IS VERY LARGE AND HEAVY. Two or
more people are required when reversing the door.
Failure to follow the warnings below can result in
damage to the dryer, property damage or injury to
persons.
• To avoid damage to the dryer or the door, support
the door with a stool or box that fits under the
door, or have an assistant support the weight of
the door.
• Always reverse the door BEFORE stacking the
dryer on top of the washer.
• Avoid dropping the door to avoid damage to the
door or the floor.
INSTALLATION
Frame L
Frame R