LG DLEX9500K Owners Manual - Page 31

Installation Test Duct Check

Get LG DLEX9500K PDF manuals and user guides View all LG DLEX9500K manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

ENGLISH INSTALLATION 31 Installation Test (Duct Check) Once you have completed the installation of the dryer, use this test to make sure the condition of the exhaust system is adequate for proper operation of the dryer. This test should be performed to alert you to any serious problems in the exhaust system of your home. • Your dryer features Flow SenseTM, an innovative sensing system that automatically detects blockages and restrictions in dryer ductwork. Keeping ductwork clean of lint buildup and free of restrictions allows clothes to dry faster and reduces energy use. NOTE The dryer should be cool before starting this test. If the dryer was warmed up during installation, run the AIR DRY cycle for a few minutes to reduce the interior temperature. To activate the Installation test: 1. Remove the drying literature, and then close the door. Do not load anything in the drum for this test, as it may affect the accuracy of the results. 4. Check the display for results. During the test cycle, monitor the Flow SenseTM display on the control panel. If the Flow Sense indicator text lights up, the exhaust system is restricted. If the indicator text remains dark, the exhaust system is adequate. Other problems may also be shown with error codes. Refer to the next page for error code details and solutions. DARK: OK LIGHTED: RESTRICTED Have the system checked immediately, as performance will be poor. 5. End of cycle. At the end of the test cycle, will display. The test cycle will end and the dryer will shut off automatically after a short delay. 2. A fter you are pressed of Power button, you will press and hold the Temp. and Signal buttons in 0.5 seconds. This button sequence activates the installation test. The code will display if the activation is successful. 3. Press and hold the Start button. The dryer will start the test, which will last about two minutes. The heat will be turned on and the temperatures in the drum will be measured.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
31
ENGLISH
Installation Test (Duct Check)
Once you have completed the installation of the dryer,
use this test to make sure the condition of the exhaust
system is adequate for proper operation of the dryer.
This test should be performed to alert you to any serious
problems in the exhaust system of your home.
• Your dryer features
FLOW SENSE
TM
, an innovative
sensing system that automatically detects blockages
and restrictions in dryer ductwork. Keeping ductwork
clean of lint buildup and free of restrictions allows
clothes to dry faster and reduces energy use.
To activate the Installation test:
1.
Remove the drying literature, and then close the
door.
Do not load anything in the drum for this test, as it
may affect the accuracy of the results.
2.
After you are pressed of Power button, you will
press and hold the Temp. and Signal buttons in
0.5 seconds.
This button sequence activates the installation test.
The code
will display if the activation is
successful.
3.
Press and hold the Start button.
The dryer will start the test, which will last about
two minutes. The heat will be turned on and the
temperatures in the drum will be measured.
4.
Check the display for results.
During the test cycle, monitor the FLOW SENSE
TM
display on the control panel. If the Flow Sense
indicator text lights up, the exhaust system is
restricted. If the indicator text remains dark, the
exhaust system is adequate.
Other problems may also be shown with error codes.
Refer to the next page for error code details and
solutions.
Have the system checked immediately, as performance
will be poor.
5.
End of cycle.
At the end of the test cycle,
will display.
The test cycle will end and the dryer will shut off
automatically after a short delay.
NOTE
The dryer should be cool before starting this test. If
the dryer was warmed up during installation, run the
AIR DRY cycle for a few minutes to reduce the interior
temperature.
DARK:
OK
LIGHTED:
RESTRICTED
INSTALLATION