LG LWD3063BD Owners Manual - Installation Guide - Page 7

Caution - double oven

Page 7 highlights

ENGLISH Part 2 INSTALLATION REQUIREMENTS 4 PREPARATION FOR MOVING THE OVEN The second step of the installation is to remove any packing material from the oven before installing the oven. 1. Remove all tape from around the oven. 2. Open the oven door and remove packaging materials and oven racks inside the oven. 3. Door removal is not a requirement for installation of the oven, but is an added convenience. To remove the door, follow the steps below. Step. 1 Fully open the door. Step. 2 Pull the hinge locks up towards the door's frame, to the unlocked position. Slot Hinge lock Lock Unlock Step. 3 Firmly grasp both sides of the door at the top. Step. 4 Close door to the door removal position, which is approximately 5 degrees. about 5 Step. 5 Lift door up and out until the hinge arm is clear of the slot. 4. Place the oven on a table or platform even with the cutout opening. (The table or platform must support 190 lbs [86 Kg] for a single built-in oven, 325 lbs [147 Kg] for a double built-in oven.) 5. Remove the metal bottom trim from the oven. It will be installed at the end of the installation process. The trim is wrapped separately and taped to the top of the unit. CAUTION • Make sure the cabinets and wall coverings around the oven can withstand the temperature (up to 194 °F [90 °C]) generated by the oven. - Discoloration, delamination or melting may occur. CAUTION • DO NOT remove spacers on the side walls of the built-in oven. - These spacers center the oven in the space provided. The oven must be centered to prevent excess heat buildup that may result in heat damage or fire. IMPORTANT NOTE • Do not lift the door by the handle. The oven door is very heavy. Firmly grasp the door by the sides before lifting it off the hinges. • Do not lay the oven door on its handle. Doing so may cause dents or scratches. • Use two or more people to lift or move the oven into the cabinet opening. Use caution when lifting the oven and wear gloves to protect hands from any sharp edges. Failure to follow these instructions may result in injury. Spacer - 7 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28

- 7 -
ENGLISH
INSTALLATION REQUIREMENTS
Part 2
4. Place the oven on a table or platform even with the cutout opening. (The table or platform must support
190 lbs
[86 Kg] for a single built-in oven, 325 lbs [147 Kg] for a double built-in oven.)
5. Remove the metal bottom trim from the oven. It will be installed at the end of the installation process. The trim
is wrapped separately and taped to the top of the unit.
Step. 1
Fully open the door.
Hinge
lock
Slot
Lock
Unlock
Step. 2
Pull the hinge locks up
towards the door's
frame, to the unlocked
position.
Step. 3
Firmly grasp both sides of the door at the top.
Step. 4
about 5
Close door to the door removal
position, which is approximately
5 degrees.
Step. 5
Lift door up and out until the
hinge arm is clear of the slot.
IMPORTANT NOTE
• Do not lift the door by the handle. The oven door is very
heavy. Firmly grasp the door by the sides before lifting
it off the hinges.
• Do not lay the oven door on its handle. Doing so may
cause dents or scratches.
• Use two or more people to lift or move the oven into
the cabinet opening. Use caution when lifting the oven
and wear gloves to protect hands from any sharp
edges. Failure to follow these instructions may result in
injury.
Spacer
4
PREPARATION FOR MOVING THE OVEN
The second step of the installation is to remove any packing material from the oven before installing the oven.
1. Remove all tape from around the oven.
2. Open the oven door and remove packaging materials and oven racks inside the oven.
3. Door removal is not a requirement for installation of the oven, but is an added convenience.
To remove the door, follow the steps below.
• Make sure the cabinets and wall
coverings around the oven can
withstand the temperature (up to
194 °F [90 °C]) generated by the oven.
- Discoloration, delamination or melting may occur.
CAUTION
• DO NOT remove spacers on the side
walls of the built-in oven.
- These spacers center the oven in the space
provided. The oven must be centered to prevent
excess heat buildup that may result in heat damage
or fire.
CAUTION