Home » Lantronix Manuals » Hubs & Switches » Lantronix SISPM1040-362-LRT » Manual Viewer

Lantronix SISPM1040-362-LRT Web User Guide Rev J PDF 16.42 MB - Page 64

Version, Read Community, Write Community, Engine ID, Apply, Reset

View all Lantronix SISPM1040-362-LRT manuals

Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

Lantronix SISPM1040-384-LRT-C & -362-LRT Web User Guide Version : Indicates the SNMP supported version. Possible versions are: SNMP v1: Set SNMP supported version 1. SNMP v2c: Set SNMP supported version 2c. SNMP v3: Set SNMP supported version 3. Read Community : Indicates the community read access string to permit access to SNMP agent. The allowed string length is 0 to 255, and the allowed content is the ASCII characters from 33 to 126. The field is applicable only when SNMP version is SNMPv1 or SNMPv2c. If SNMP version is SNMPv3, the community string will be associated with SNMPv3 communities table. It provides more flexibility to configure security name than a SNMPv1 or SNMPv2c community string. In addition to community string, a particular range of source addresses can be used to restrict source subnet. Write Community : Indicates the community write access string to permit access to SNMP agent. The allowed string length is 0 to 255 characters, and the allowed content is ASCII characters 33 - 126. The field is applicable only when SNMP version is SNMPv1 or SNMPv2c. If SNMP version is SNMPv3, the community string will be associated with SNMPv3 communities table. It provides more flexibility to configure security name than a SNMPv1 or SNMPv2c community string. In addition to community string, a particular range of source addresses can be used to restrict source subnet. At the dropdown next to the field, select Enabled or Disabled. The default is Write Community Enabled. Engine ID : Indicates the SNMPv3 engine ID. The string must contain an even number (in hexadecimal format) with number of digits between 10 and 64, but all-zeros and all-'F's are not allowed. Change of the Engine ID will clear all original local users. Buttons: Apply - Click to save changes. Reset- Click to undo any changes made locally and revert to previously saved values. 33728 Rev. J https://www.lantronix.com/ Page 64 of 499

Section	Page
Safety Warnings and Cautions	3
Chapter 1 Introduction	9
1-1 About This Manual	9
1-2 Related Documentation	9
1-3 Product Descriptions	9
1-5 Ordering Information	10
Services (order separately)	10
1-6 Web-based Management	11
1-7 Initial Configuration	11
1-8 Web Navigation	12
1-9 First Time Wizard	14
1-10 Menu System	17
Chapter 2 System Configuration	18
2-1 System	18
2-1.1 Information	18
2-1.2 IP	19
2-1.3 NTP	25
2-1.4 Time	27
2-1.5 Log	29
2-1.6 Digital I/O	30
2-1.7 Alarm Notification	31
2-1.7.1 Trap Event Severity	31
2-1.7.2 Port Event Setting	33
2-2 Green Ethernet	35
2-2.1 Port Power Savings	35
2-3 Ports Configuration	37
2-3.1 Ports	37
2-3.2 Ports Description	39
2-4 DHCP	40
2-4.1 Server	40
2-4.1.1 Mode	40
2-4.1.2 Excluded IP	42
2-4.1.3 Pool	43
2-4.2 Snooping	47
2-4.3 Relay	49
2-5 Security	51
2-5.1 Switch	51
2-5.1.1 Users	51
2-5.1.2 Privilege Levels	53
2-5.1.3 Authentication Method	55
2-5.1.4 HTTPs	58
2-5.1.6 Access Management	61
2-5.1.7 SNMP	63
2-5.1.7.1 System	63
2-5.1.7.2 Trap	65
Messages:	66
The value of ‘Trap Destination Address’ is 0.0.0.0. Do you want to proceed anyway?	66
‘Trap Configuration Name’ string is null	66
Example:	67
You can click a linked Trap Name to go to its SNMP Trap Configuration page as described above.	67
2-5.1.7.3 Communities	68
2-5.1.7.4 Users	69
2-5.1.7.5 Group	71
2-5.1.7.6 Views	72
2-5.1.7.7 Access	73
2-5.1.8 RMON	74
2-5.1.8.1 Statistics	74
2-5.1.8.2 History	75
2-5.1.8.3 Alarm	76
2-5.1.8.4 Event	78
2-5.2 Network	79
2-5.2.1 Limit Control	79
2-5.2.2 NAS	82
2-5.2.3 ACL	88
2-5.2.3.1 Ports	88
2-5.2.3.2 Rate Limiters	90
2-5.2.3.3 Access Control List	91
2-5.2.4 IP Source Guard	100
2-5.2.4.1 Configuration	100
2-5.2.4.2 Static Table	102
2-5.2.5 ARP Inspection	103
2-5.2.5.1 Port Configuration	103
2-5.2.5.2 VLAN Configuration	105
2-5.2.5.3 Static Table	107
2-5.2.5.4 Dynamic Table	108
2-5.3 AAA	110
2-5.3.1 RADIUS	110
This page lets you configure up to five RADIUS servers. RADIUS (Remote Authentication Dial In User Service) is a networking protocol that provides centralized Authentication, Authorization, and Accounting ‘(AAA’ or ‘Triple A’) management for users who...	110
RADIUS uses two packet types to manage the full AAA process: Access-Request, which manages authentication and authorization; and Accounting-Request, which manages accounting. Authentication and authorization are defined in IETF RFC 2865 and accounting...	110
2-5.3.2 TACACS+	113
2-6 Aggregation	115
2-6.1 Static	115
2-6.2 LACP	117
2-6.2 LACP on Air	119
2-7 Link OAM	120
2-7.1 Port Settings	120
2-7.2 Event Settings	122
2-8 Loop Protection	124
2-9 Spanning Tree	126
2-9.1 Bridge Setting	126
2-9.2 MSTI Mapping	129
2-9.3 MSTI Priorities	131
2-9.4 CIST Ports	133
2-9.5 MSTI Ports	135
2-10 IPMC Profile	137
2-10.1 Profile Table	137
2-10.2 Address Entry	139
2-11 MVR	140
2-12 IPMC	143
2-12.1 IGMP Snooping	143
2-12.1.1 Basic Configuration	143
2-12.1.2 VLAN Configuration	146
2-12.1.3 Port Filtering Profile	148
2-12.2 MLD Snooping	151
2-12.2.1 Basic Configuration	151
2-12.2.2 VLAN Configuration	154
2-12.2.3 Port Group Filtering	156
2-13 LLDP	159
2-13.1 LLDP	159
2-13.2 LLDP-MED	162
2-14 PoE	167
2- 14.1 Configuration	167
2- 14.2 Power Delay	170
2- 14.3 Schedule Profile	171
2- 14.4 PoE Auto Power Reset (Auto Checking)	173
2- 14.5 Chip Reset Schedule	175
2-15 EPS	176
2-16 MEP	180
Instance Data	181
Instance Configuration	182
2-17 ERPS	186
2-18 MAC Table	191
2-19 VLAN Translation	193
2- 19.1 Port to Group Mapping	193
2- 19.2 VID Translation Mapping	195
2-20 VLANs	197
2-21 Private VLANs	200
2-21.1 Membership	200
2-21.2 Port Isolation	202
2-22 VCL	203
2-22.1 MAC-based VLAN	203
2-22.2 Protocol -based VLAN	205
2-22.2.1 Protocol to Group	205
2-22.2.2 Group to VLAN	207
2-22.3 IP Subnet-based VLAN	208
2-23.1 Configuration	209
2-23.2 OUI	211
2-24 Ethernet Services	212
2-24.1 Ports	212
2-24.2 Bandwidth Profiles	215
2-24.3 EVCs	217
2-24.4 ECEs	220
2-25 QoS	227
2-25.1 Port Classification	227
2-25.2 Port Policing	230
2-25.4 Port Scheduler	232
2-25.5 Port Shaping	234
2-25.6 Port Tag Remarking	236
2-25.7 Port DSCP	239
2-25.8 DSCP-Based QoS	241
2-25.9 DSCP Translation	243
2-25.10 DSCP Classification	245
2-25.11 QoS Control List	247
2-25.12 Storm Control	251
2-26 Mirroring and Remote Mirroring	252
2-27 UPnP	256
2-28 PTP	257
2-29. GVRP	262
2-29.2 Port Config	264
2-30. sFlow	265
2-31 UDLD	267
2-32 Rapid Ring	269
2-33 ConsoleFlow and LPM	271
Supported Firmware Versions	271
ConsoleFlow Agent Configuration	271
2-34 MRP	274
2-35 SMTP	277
Chapter 3 Monitor	279
3-1 System	279
3-1.1 Information	279
3-1.2 IP Status	281
3-1.3 Log	283
3-1.4 Detailed Log	285
3-2 Green Ethernet	286
3-2.1 Port Power Savings	286
3-3 Ports	287
3-3.1 Traffic Overview	287
3-3.2 QoS Statistics	289
3-3.3 QCL Status	290
3-3.4 Detailed Statistics	292
3-3.5 SFP Information	294
3-3.6 SFP Detail Info	296
3-4 Link OAM	298
3-4.1 Statistics	298
3-4.2 Port Status	300
3-4.3 Event Status	302
3-5 DHCP	305
3-5.1 Server	305
3-5.1.1 Statistics	305
3-5.1.2 Binding	307
3-5.1.3 Declined IP	310
3-5.2 Snooping Table	311
3-5.3 Relay Statistics	312
3-5.4 Detailed Statistics	314
3-6 Security	316
3-6.1 Access Management Statistics	316
3-6.2 Network	317
3-6.2.1 Port Security	317
3-6.2.1.1 Switch	317
This page shows the Port Security status. Port Security is a module with no direct configuration. Configuration comes indirectly from other modules - the user modules. When a user module has enabled port security on a port, the port is set-up for soft...	317
3-6.2.1.2 Port	319
MAC Address and VLAN ID : The MAC address and VLAN ID that are seen on this port. If no MAC addresses are learned, a single row stating \	319
State : Indicates whether the corresponding MAC address is blocked or forwarding. In the blocked state, it will not be allowed to transmit or receive traffic.	319
Time of Addition : Shows the date and time when this MAC address was first seen on the port.	319
Age/Hold : If at least one user module has decided to block this MAC address, it will stay in the blocked state until the hold time (measured in seconds) expires. If all user modules have decided to allow this MAC address to forward, and aging is enab...	319
If aging is disabled or a user module has decided to hold the MAC address indefinitely, a dash (-) displays.	319
Buttons	320
Auto-refresh: Check this box to refresh the page automatically every 3 seconds.	320
Refresh: Click to manually refresh the page immediately.	320
Clear : Clears the page data.	320
3-6.2.2 NAS	321
3-6.2.2.1 Switch	321
RADIUS-Assigned VLAN : RADIUS-assigned VLAN provides a means to centrally control the VLAN on which a successfully authenticated supplicant is placed on the switch. Incoming traffic will be classified to and switched on the RADIUS-assigned VLAN. The R...	322
Buttons	322
Auto-refresh: Check this box to refresh the page automatically every 3 seconds.	322
Refresh: Click to manually refresh the page immediately.	322
3-6.2.2.2 Port	323
3-6.2.3 ACL Status	326
3-6.2.4 ARP Inspection	328
3-6.2.5 IP Source Guard	329
3-6.3 AAA	330
3-6.3.1 RADIUS Overview	330
3-6.3.2 RADIUS Details	332
3-6.4 Switch	337
3-6.4.1 RMON	337
3-6.4.1.1 Statistics	337
3-6.4.1.2 History	340
3-6.4.1.3 Alarm	342
3-6.4.1.4 Event	343
3-7 Aggregation	344
3-7.1 Status	344
3-7.2 LACP	345
3-7.2.1.1 System Status	345
3-7.2.1.2 Port Status	346
3-7.2.1.3 Port Statistics	347
3-8 Loop Protection	348
3-9 Spanning Tree	349
3-9.1 Bridge Status	349
3-9.2 Port Status	352
3-9.3 Port Statistics	353
3-10 MVR	354
3-10.1 Statistics	354
3-10.2 MVR Channels Groups	355
3-10.3 MVR SFM Information	356
3-11 IPMC	357
3-11.1 IGMP Snooping	357
3-11.1.1 Status	357
3-11.1.2 Group Information	359
3-11.1.3 IPv4 SFM Information	360
3-11.2 MLD Snooping	361
3-11.2.1 Status	361
3-11.2.2 Group Information	363
3-11.2.3 IPv6 SFM Information	364
3-12 LLDP	365
3-12.1 Neighbor	365
3-12.2 LLDP-MED Neighbor	368
3-12.3 PoE	371
3-12.4 EEE	372
3-12.5 Port Statistics	374
3-13 Ethernet Services	376
3-13.1 EVC Statistics	376
3-14 PTP	378
3-15 PoE	385
3-16 MAC Table	387
3-17 VLANs	389
3-17.1 Membership	389
3-17.2 Port	391
3-18 MRP	394
3-18.1 Media Redundancy Protocol Status	394
3-19 VCL	396
3-19.1 MAC-based VLAN	396
3-18.2 Protocol-based VLAN	397
3-18.2.1 Protocol to Group	397
3-18.2.2 Group to VLAN	399
3-18.3 IP Subnet-based VLAN	400
3-19 sFlow	401
3-20 UDLD	403
Chapter 4 Diagnostics	404
4-1 Ping	404
4-2 Ping6	406
4-3 Cable Diagnostics	408
4-4 Traceroute	410
4-5 Link OAM	412
4-5.1 MIB Retrieval	412
Chapter 5 Maintenance	413
5-1 Restart Device	413
5-2 Reboot Schedule	414
5-3 Factory Defaults	415
5-4 Firmware	416
5-4.1 Firmware Upgrade	416
5-4.2 Firmware Selection	418
5-5 Configuration	420
5-5.1 Save running-config to startup-config	420
5-5.2 Download	421
5-5.3 Upload	423
5-5.4 Activate	425
5-5.5 Delete	428
5-6 Server Report	429
Chapter 6 DMS (Device Management System)	430
6-1 DMS Introduction	430
6-2 About DMS Mode	430
6-4 DMS Icons and Controls	431
6-4-1 Topology View Icons / Controls	432
6-4-2 Device Consoles (Dashboard / Notification / Monitor)	432
Dashboard Console	432
Settings Consoles (Device / Group / Config)	433
Floor View	433
Map View	433
Scan Devices on Different VLANs via DMS	433
6-5 DMS Mode	434
6-6 Google Map API Key Configuration	435
6.6.1 Google Map API Key Configuration	435
6.6.2 Get the Google Map API Key	435
6-7 Device List	436
6.8 DMS > Maintenance > Floor Image	439
6.9 DMS > Maintenance > Diagnostics	442
Chapter 7 DMS > Graphical Monitoring	444
7-1 Topology View	444
7-2 Floor View	449
7-3 Map View	451
Chapter 8 DMS > Maintenance	453
8-1 Floor Image	453
8-2 Diagnostics	455
8-3 Traffic Monitor	457
PoE Auto Power Reset “AutoFill” Feature	460
8-4 Troubleshooting DMS	463
Appendix A Rapid Ring Operation	464
A-1 Rapid Ring Operation	464
A-1-1 Single Ring	464
A-1-2 Ring to Ring	466
A-1-3 Dual Ring	467
A-1-4 Rapid Chain	468
A-1-5 Hardware Setting and Status for Ring	469
Ring Setting by DIP Switch	469
RM and RC LED Descriptions	470
Appendix B. DHCP Per Port	471
Appendix C MRP Pre-Requisites and Application Examples	475
MRP Description	475
MRP Operation	475
Related Devices	476
MRP Sample Setup	476
MRP Pre-Requisites (General)	476
MRP Web UI Configuration	477
Example 1: MRP Manager Re-Config (Web UI)	479
Example 2: Non-Blocking MRC State Recognized by MRM (Web UI)	480
Example 3: MRP Roles Set in Web UI	480
Appendix D G.8032 Major and Sub Rings Configuration	481
Introduction	481
Basic Concepts	481
IP Addresses	481
Sample Configuration	482
Switch 1 Configuration (SISPM1040-582-LRT)	483
Switch 2 Configuration (SISPM1040-384-LRT-C)	484
Switch 3 Configuration (SISPM1040-362-LRT [W])	485
Switch 4 Configuration (SISPM1040-362-LRT [E])	486
Testing	487
Testing Pings from Switch 4 to Switch 1 – Major Ring	487
Testing Pings from Switch 4 to Switch 3 – Sub Ring	488
Config files	489
running-config_192.168.1	489
running-config_192.168.1.1	491
running-config_192.168.1	494

Match case Limit results 1 per page

Lantronix

SISPM1040-384-LRT-C & -362-LRT Web User Guide

33728 Rev. J

https://www.lantronix.com/

Page

499

Version :

Indicates the SNMP supported version. Possible versions are:

SNMP v1

Set SNMP supported version 1.

SNMP v2c

Set SNMP supported version 2c.

SNMP v3

Set SNMP supported version 3.

Read Community :

Indicates the community read access string to permit access to SNMP agent.

The allowed string length is 0 to 255, and the allowed content is the ASCII characters from 33 to 126.

The field is applicable only when SNMP version is SNMPv1 or SNMPv2c. If SNMP version is SNMPv3,

the community string will be associated with SNMPv3 communities table. It provides more flexibility to

configure security name than a SNMPv1 or SNMPv2c community string. In addition to community string,

a particular range of source addresses can be used to restrict source subnet.

Write Community :

Indicates the community write access string to permit access to SNMP agent.

The allowed string length is 0 to 255 characters, and the allowed content is ASCII characters 33 - 126.

The field is applicable only when SNMP version is SNMPv1 or SNMPv2c. If SNMP version is SNMPv3, the

community string will be associated with SNMPv3 communities table. It provides more flexibility to

configure security name than a SNMPv1 or SNMPv2c community string. In addition to

community string, a particular range of source addresses can be used to restrict source

subnet.

At the dropdown next to the field, select

Enabled

Disabled

. The default is Write Community

Enabled.

Engine ID :

Indicates the SNMPv3 engine ID. The string must contain an even number (in hexadecimal

format) with number of digits between 10 and 64, but all-zeros and all-'F's are not allowed. Change of the

Engine ID will clear all original local users.

Buttons:

Apply

– Click to save changes.

Reset-

Click to undo any changes made locally and revert to previously saved values.