Lantronix XPort AR XPort AR - User Guide - Page 64

SNMP Settings, To con PPP, Line1, PPP Configuration, Submit.

Get Lantronix XPort AR PDF manuals and user guides View all Lantronix XPort AR manuals
Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

9: Service Settings Note: The following section describes the steps to configure PPP 1 (PPP on serial line 1); these steps also apply to any line instance of the device. To configure PPP: 1. Click PPP on the menu bar and Line1 at the top of the page. The PPP on Line 1 - Configuration page appears. Figure 9-2 PPP Configuration Settings 2. Enter or modify the following settings: PPP Configuration Settings Local IP Address Peer IP Address Authentication Mode Username Password 3. Click Submit. Table 9-3 PPP Configuration Description Enter the IP address assigned to the device's PPP interface. Enter the IP address assigned to the peer (when requested during negotiation). Choose the authentication mode:  None = no authentication is required  PAP = Password Authentication Protocol  CHAP = Challenge Handshake Authentication Protocol  Enter a username if authentication is to be used on the PPP interface. The peer must be configured to use the same username. Enter a password if authentication is to be used on the PPP interface. The peer must be configured to use the same password. SNMP Settings XPort AR User Guide 64

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
9: Service Settings
XPort AR User Guide
64
Note:
The following section describes the steps to configure PPP 1 (PPP on serial line
1); these steps also apply to any line instance of the device.
To configure PPP:
1.
Click
PPP
on the menu bar and
Line1
at the top of the page. The PPP on Line 1 –
Configuration page appears.
Figure 9-2
PPP Configuration Settings
2.
Enter or modify the following settings:
Table 9-3
PPP Configuration
3.
Click
Submit.
SNMP Settings
PPP Configuration Settings
Description
Local IP Address
Enter the IP address assigned to the device’s PPP interface.
Peer IP Address
Enter the IP address assigned to the peer (when requested during
negotiation).
Authentication Mode
Choose the authentication mode:
None
= no authentication is required
PAP
= Password Authentication Protocol
CHAP
= Challenge Handshake Authentication Protocol
Username
Enter a username if authentication is to be used on the PPP
interface.
The peer must be configured to use the same username.
Password
Enter a password if authentication is to be used on the PPP interface. The peer must be configured to
use the same password.