Lenovo E100 Hardware Maintenance Manual - Page 103

Replacing, drive

Get Lenovo E100 PDF manuals and user guides View all Lenovo E100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 103 highlights

Replacing a hard disk drive Important When you install a new hard disk drive, you also need a set of Product Recovery discs. The set of Product Recovery discs will enable the contents of the hard disk to be restored to the same state as when the computer was originally shipped from the factory. For more information on recovering factory-installed software, refer to "Recovering software" in the User Guide. 1. Remove the covers. See "Removing the covers" on page 86. 2. Disconnect the signal and power cables from the rear of the hard disk drive. 3. Remove the two screws at the rear of the right side cover and slide the cover to the rear to remove. 4. Remove the two screws that secure the drive on each side. Chapter 8. Replacing FRUs (Type 9626) 97

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
Replacing
a
hard
disk
drive
Important
When
you
install
a
new
hard
disk
drive,
you
also
need
a
set
of
Product
Recovery
discs.
The
set
of
Product
Recovery
discs
will
enable
the
contents
of
the
hard
disk
to
be
restored
to
the
same
state
as
when
the
computer
was
originally
shipped
from
the
factory.
For
more
information
on
recovering
factory-installed
software,
refer
to
“Recovering
software”
in
the
User
Guide
.
1.
Remove
the
covers.
See
“Removing
the
covers”
on
page
86.
2.
Disconnect
the
signal
and
power
cables
from
the
rear
of
the
hard
disk
drive.
3.
Remove
the
two
screws
at
the
rear
of
the
right
side
cover
and
slide
the
cover
to
the
rear
to
remove.
4.
Remove
the
two
screws
that
secure
the
drive
on
each
side.
Chapter
8.
Replacing
FRUs
(Type
9626)
97