Lenovo H520 Lenovo H520s Hardware Maintenance Manual - Page 40

Replacing the Power supply, cables - motherboard

Get Lenovo H520 PDF manuals and user guides View all Lenovo H520 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

Step 6. Remove the memory module being replaced by opening the retaining clips as shown. Step 7. Position the new memory module over the memory connector. Make sure the notch 1 on the memory module is correctly aligned with the connector key 2 on the system board. Push the memory module straight down into the connector until the retaining clips close. Step 8. Reattach the computer cover. Replacing the Power supply Note: For this procedure, it helps to lay the computer flat. To replace the Power supply: Step 1. Step 2. Step 3. Step 4. Step 5. Step 6. Step 7. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices. Unplug all power cords from electrical outlets. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. Refer to "Left and right view" and "Rear view" for help with locating the various connectors. Remove the computer cover. Refer to "Removing the computer cover". Remove the front bezel. Refer to "Removing the front bezel". Disconnect the power cables from the connectors on motherboard. Remove the 3 screws that secure the Power supply to the chassis. 34 Lenovo H520sHardware Maintenance Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
Step 6.
Remove the memory module being replaced by opening the retaining clips as shown.
Step 7.
Position the new memory module over the memory connector. Make sure the notch
1
on the
memory module is correctly aligned with the connector key
2
on the system board. Push the
memory module straight down into the connector until the retaining clips close.
Step 8.
Reattach the computer cover.
Replacing the Power supply
Note:
For this procedure, it helps to lay the computer flat.
To replace the Power supply:
Step 1.
Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating
system, and turn off the computer and all attached devices.
Step 2.
Unplug all power cords from electrical outlets.
Step 3.
Disconnect all cables attached to the computer. This includes power cords, input/output (I/O)
cables, and any other cables that are connected to the computer. Refer to “Left and right view”
and “Rear view” for help with locating the various connectors.
Step 4.
Remove the computer cover. Refer to “Removing the computer cover”.
Step 5.
Remove the front bezel. Refer to “Removing the front bezel”.
Step 6.
Disconnect the power cables from the connectors on motherboard.
Step 7.
Remove the 3 screws that secure the Power supply to the chassis.
34
Lenovo H520sHardware Maintenance Manual