Lenovo NetVista Hardware Maintenance Manual (HMM) for IBM NetVista 6029 system - Page 36

Installing a drive, Notes

Get Lenovo NetVista PDF manuals and user guides View all Lenovo NetVista manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

The following table describes some of the drives that can be installed in each bay and their height requirements. 1 Bay 1 - Maximum height: 43.0 mm (1.7 in.) 2 Bay 2 - Maximum height: 43.0 mm (1.7 in.) 3 Bay 3 - Maximum height: 25.8 mm (1.0 in.) 4 Bay 4 - Maximum height: 25.8 mm (1.0 in.) CD-ROM drive (preinstalled in some models) 5.25-inch hard disk drive 5.25-inch hard disk drive 3.5-inch hard disk drive (requires a mounting bracket) CD-ROM drive DVD-ROM drive CD-RW drive 3.5-inch diskette drive (preinstalled) 3.5-inch hard disk drive Notes: 1. Drives that are greater than 43.0 mm (1.7 in.) high cannot be installed. 2. Install removable media (tape or CD) drives in the accessible bays (bay 1 or 2). Installing a drive To install an internal drive, follow these steps: 1. Remove the cover. See "Removing the cover" on page 23. 2. If the computer has a CD drive or DVD drive, you might need to remove the signal and power cables from the drive. 3. Remove the bay panel from the drive bay by inserting a flat-blade screwdriver at the end and gently prying it loose. 4. Remove the metal shield from the drive bay by inserting a flat-blade screwdriver into one of the slots and gently prying it loose. 5. Make sure the drive that you are installing is set correctly as either a master or a slave device. v If it is the first CD drive or DVD drive, set it as a master device. 30 Hardware Maintenance Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
The following table describes some of the drives that can be installed in each bay
and their height requirements.
±1²
Bay 1 - Maximum height: 43.0 mm (1.7 in.)
CD-ROM drive (preinstalled in some
models)
5.25-inch hard disk drive
±2²
Bay 2 - Maximum height: 43.0 mm (1.7 in.)
5.25-inch hard disk drive
3.5-inch hard disk drive (requires a
mounting bracket)
CD-ROM drive
DVD-ROM drive
CD-RW drive
±3²
Bay 3 - Maximum height: 25.8 mm (1.0 in.)
3.5-inch diskette drive (preinstalled)
±4²
Bay 4 - Maximum height: 25.8 mm (1.0 in.)
3.5-inch hard disk drive
Notes:
1.
Drives that are greater than 43.0 mm (1.7 in.) high cannot be installed.
2.
Install removable media (tape or CD) drives in the accessible bays (bay 1 or 2).
Installing a drive
To install an internal drive, follow these steps:
1.
Remove the cover. See
“
Removing the cover
”
on page 23.
2.
If the computer has a CD drive or DVD drive, you might need to remove the
signal and power cables from the drive.
3.
Remove the bay panel from the drive bay by inserting a flat-blade screwdriver
at the end and gently prying it loose.
4.
Remove the metal shield from the drive bay by inserting a flat-blade
screwdriver into one of the slots and gently prying it loose.
5.
Make sure the drive that you are installing is set correctly as either a master or
a slave device.
v
If it is the first CD drive or DVD drive, set it as a master device.
30
Hardware Maintenance Manual